⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

Need TIG recommendation

A young fella at work thinks he wants a TIG welder to work with thin aluminum piping. He is big on hot rod modification...
11 comments posted 14yrs
posted by dgriff23
11 comments posted 14yrs posted by dgriff23

I'm getting confused

As you know, my Lincoln 175 +SP was acting up. I borrowed a Miller 175 wire feed. Yesterday, I had the chance to weld 1...
17 comments posted 14yrs
posted by steveb
17 comments posted 14yrs posted by steveb

weldolet welding

As per ASME B31.3 Run pipe 6" Sch 160 with Tee butt branch of weldolet 2" Sch 160 to be welded. what is the thickness o...
1 comments posted 15yrs
posted by smohdkhaleel
1 comments posted 15yrs posted by smohdkhaleel

Titanium welding help please

I have a part with cosmetic damage that may need to be weld repaired. The part is 6al4v alloy. It is 1.2" in diameter a...
6 comments posted 15yrs
posted by etpm
6 comments posted 15yrs posted by etpm

Rotary welding table project

--Put up some more photos; it's nearing completion but I still need a better way to spring the footpedal back to 'off'.....
0 comments posted 15yrs
posted by steamer
0 comments posted 15yrs posted by steamer

What is the right gun for Miller S-52E wirefeed

I have a Miller Pulstar 450 amp MIG welder and an S-52 wirefeed. It does not have a gun, which is my fault (forgot to t...
2 comments posted 15yrs
posted by ignoramus1358
2 comments posted 15yrs posted by ignoramus1358

What is adequate ventilation?

So I'm in the process of setting up a small fabrication shop in an extra garage(as a business) and am currently trying...
9 comments posted 15yrs
posted by mkzero
9 comments posted 15yrs posted by mkzero

MIG brazing particulars

I'd like to try MIG brazing with silicon bronze wire, but have a couple of questions. 1. Is my Lincoln 135SP up to it?...
8 comments posted 15yrs
posted by bobengelhardt
8 comments posted 15yrs posted by bobengelhardt

Rosebud weld tactics

I'm going to drill some holes in one side of two pieces of flat, and then use rosebud welds to join them together. Is i...
10 comments posted 15yrs
posted by pittmanpirate
10 comments posted 15yrs posted by pittmanpirate

Durty wurds

Well, I got two connectors today for some 1/4" coppertubing. Used mapp gas. Used Alum oxide sandpaper to clean. Used fl...
4 comments posted 15yrs
posted by pittmanpirate
4 comments posted 15yrs posted by pittmanpirate

Victor cutting torches

I've been leaning towards buying a smaller Victor cutting torch. I have the bigger 351. The other day, I had to cut som...
8 comments posted 15yrs
posted by pittmanpirate
8 comments posted 15yrs posted by pittmanpirate

Campbell Hausfeld Oxy-Acetylene

Has anyone here had an opportunity to use a Campbell Hausfeld Oxy-Acetylene Torch Kit? If so how would you rate it for m...
5 comments posted 15yrs
posted by mwashingtonlll_at_verizon_dot_
5 comments posted 15yrs posted by mwashingtonlll_at_verizon_dot_

Solder question

Is there any danger in using solder on a copper tube that will be immersed in beer brew that will eventually be drunk?...
3 comments posted 15yrs
posted by pittmanpirate
3 comments posted 15yrs posted by pittmanpirate

Amazing Brazing

This came up on a bicycle frame building list that I am on. Probably the best video of brazing that I have seen. http://...
8 comments posted 15yrs
posted by dave.dillabough
8 comments posted 15yrs posted by dave.dillabough

6 Welders

Here they are in my garage. http://goo.gl/o6s7l The on on the far right is the best, TIG/MIG/Stick welder Thermal Arc 4...
9 comments posted 15yrs
posted by ignoramus21395
9 comments posted 15yrs posted by ignoramus21395