⋐⋒⋐ Computer Numeric Control

  1. Home
  2. ⋐⋒⋐ Computer Numeric Control
2667 Threads Posts
to

Supplied Voltage -- 208 vs. 240

Awl -- In a thread I started in alt.home.repair (1920's wiring), a knowledgeable fellow (Bud) asserted that 208 V/3 ph...
24 comments posted 16yrs
posted by UNfitcat
24 comments posted 16yrs posted by UNfitcat

Points to ponder

Think about this: 1. Cows 2. The Constitution 3. The Ten Commandments -------------------------------------------------...
18 comments posted 16yrs
posted by gunner
18 comments posted 16yrs posted by gunner

any comments on a Hyundai lathe?

Looking at a used Hyundai HIT-18s lathe. 1995 with Siemens control. good/bad? Thank You, Randy Remove 333 from email add...
3 comments posted 16yrs
posted by rbraun333
3 comments posted 16yrs posted by rbraun333

BRIDGEPORT VMC POWER

HI ALL I'm debateing on getting Bridgeport model INT-412 1990, Full load amps 21, spindel 5.5 KW, 600V 3ph, KA 18 12 to...
1 comments posted 16yrs
posted by peter
1 comments posted 16yrs posted by peter

VTL

Anyone ever see a vertical lathe (cnc) with a tailstock I need a small one. db
0 comments posted 16yrs
posted by debco99
0 comments posted 16yrs posted by debco99

Need replacement for ProComm

OK, we've been using ProComm V4.8 for years. I just had occasion to need to reinstall it on a PC here, and, lo and beho...
3 comments posted 16yrs
posted by aus.robustus
3 comments posted 16yrs posted by aus.robustus

For Sale Enco Tool and Cutter Grinder

I picked this up recently, and have cleaned it up and tested it. Its this grinder http://www.use-enco.com/CGI/INSRIT?PM...
0 comments posted 16yrs
posted by gunner
0 comments posted 16yrs posted by gunner

SolidCam GPP settings for Hurco KMB-1

I'm new to G code and I seem to having a problem getting SolidCam to generate G code in the correct form for arcs on an...
0 comments posted 16yrs
posted by msmith5242
0 comments posted 16yrs posted by msmith5242

On Topic? Top Fuel Dragster Info.

* One Top Fuel dragster outfitted with a 500 cubic-inch Hemi engine makes more horsepower (8,000 HP) than the first 4 r...
7 comments posted 16yrs
posted by pulsar
7 comments posted 16yrs posted by pulsar

Surface Grinder question..B&S 618

On the back of the table ways is a group of roller bearings running in a double V.. V on the bottom and a matchin V on...
0 comments posted 16yrs
posted by gunner
0 comments posted 16yrs posted by gunner

CAM software Q

is there a prog out there that will import G code and provide a simulated monitor (orjust XYZ) view showing absolute po...
3 comments posted 16yrs
posted by Me
3 comments posted 16yrs posted by Me

A useful tip...roll dimensions, checking angles

Roll dimensions. People call it different things, but it's a way of checking angles on a sine plate for location. (DESC...
12 comments posted 16yrs
posted by vinny
12 comments posted 16yrs posted by vinny

Cast Iron CGI/ADI requirements

Hello, I'm writing a report about "cast iron". Could someone tell me which are the requirements of machine tools (e.g....
6 comments posted 16yrs
posted by sbicelli
6 comments posted 16yrs posted by sbicelli