⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

power transmission items

TEXSPARES CORPORATION OF INDIA 122,Narayan Dhuru street,1st floor, Shreeji Bhuvan, Mumbai-4000003. Tele: (022)56349683,...
3 comments posted 20yrs
posted by tci1973
3 comments posted 20yrs posted by tci1973

Three phase switch for single phase?

Hi group. I have a big vertical bandsaw that I would like run with a single phase motor. The saw came with a three phas...
12 comments posted 20yrs
posted by ahall
12 comments posted 20yrs posted by ahall

another tool/part ID please

I should know what this is, but... 3" long, 5/16" square, mildly hardened, with two milled grooves: http://www.token.crw...
2 comments posted 20yrs
posted by kensnews
2 comments posted 20yrs posted by kensnews

6" Craftsman/Atlas Lathe Parts

I am looking for a set of Gears for the 6" Craftsman/Atlas (AA) Lathe. Lathe #109.0703 Anyone have a set lying around th...
11 comments posted 20yrs
posted by tagarn
11 comments posted 20yrs posted by tagarn

OT: Weed killer

What is the cheapest way to defoiliate my property as we head into spring? It's not just weeds but light brush and smal...
63 comments posted 20yrs
posted by tom(nospam)
63 comments posted 20yrs posted by tom(nospam)

Taper Turning Revisited

A while back I received some very good suggestions on RCM for turning tapers. I put them to the test and turned some ta...
3 comments posted 20yrs
posted by judybob
3 comments posted 20yrs posted by judybob

Questions about roll-bender dies

1. Of the 3 rollers, only the middle one needs to fit the stock, right? The outer two are just pushing and no bending i...
0 comments posted 20yrs
posted by bobengelhardt
0 comments posted 20yrs posted by bobengelhardt

Southbend Lathe Question

I have just acquired a 10 inch Southbend lathe With a taper attachment. To engage the taper attachment I assume that th...
1 comments posted 20yrs
posted by jd.kirkes
1 comments posted 20yrs posted by jd.kirkes

Parts ID Needed

Bought a box of tools on eBay the other day. The box belonged to a tool and die maker who worked at Pratt and Whitney,...
4 comments posted 20yrs
posted by boebert
4 comments posted 20yrs posted by boebert

OT: Model Locomotives

Hi all: I recently got possession of some old (20-30's), hand built "O" scale model locomotives from the UK. They are i...
3 comments posted 20yrs
posted by FrankPhallen
3 comments posted 20yrs posted by FrankPhallen

aluminum/brass reaction?

I would like to tap a barbed fitting into the aluminum gearcase of my outboard motor. I cannot find stainless barbed fi...
5 comments posted 20yrs
posted by mark
5 comments posted 20yrs posted by mark

tosnuc 600m control

I might buy an 85 toshiba (shibaura) vmc_45 with a tosnuc 600m control. I need to know if this control is one that coul...
0 comments posted 20yrs
posted by reiss_machinist
0 comments posted 20yrs posted by reiss_machinist

OT - one wheel cycle

This would be the vehicle of choice for Burning Man don't you think. http://www.wheelsurf.nl __ "All it took was all I h...
3 comments posted 20yrs
posted by emmo
3 comments posted 20yrs posted by emmo

Home Brew Roll Bender

Here is a roll bender I just funished. It is for making curved rail components for a new deck. The material in the mach...
14 comments posted 20yrs
posted by elhollin
14 comments posted 20yrs posted by elhollin

Spark gaps -- making and triggering

I finally picked up the caps from Fermilab. Each of them weighs about 40 lbs and they look nice, very cute color also....
43 comments posted 20yrs
posted by ignoramus29428
43 comments posted 20yrs posted by ignoramus29428