⏣ General Metalworking

30777 Threads Posts
to

Drill Press or Drill/Mill Machine

Since there are no places near me that sell used machines of the type I need, it looks as though I'll have to gamble on...
20 comments posted 20yrs
posted by Searcher7
20 comments posted 20yrs posted by Searcher7

Parajust AC variable frequency drive

Dear Sir We need urgently a complete electrical & electronic drawings for Parajust AC variable frequency drive, produce...
0 comments posted 20yrs
posted by aei_ltd
0 comments posted 20yrs posted by aei_ltd

zerk fittings on motor?

I have a couple of 7.5 hp 3 phase 184 frame motors. Both have zerk fittings. I don't normally see zerk fittings on moto...
15 comments posted 20yrs
posted by grant
15 comments posted 20yrs posted by grant

Help with milling setup for novice

Hi, I have recently purchased a vertical milling machine to cut slots in front panels of enclosures for our prototypes....
18 comments posted 20yrs
posted by webreply
18 comments posted 20yrs posted by webreply

Miniature screw assortment?

Lately I seem to be wishing for itty-bitty screws. I googled around and found suppliers and cool charts but it looks li...
13 comments posted 20yrs
posted by tom(nospam)
13 comments posted 20yrs posted by tom(nospam)

OT Computer Question

Hi All; Has anyone found an adapter that will connect a PCMCIA Hard Drive (type II) to a USB port? Thanks Jack
6 comments posted 20yrs
posted by jhayes
6 comments posted 20yrs posted by jhayes

Colchester 1500: Whatsit?

Hi, I do have an offer of a "Colchester 1500". Haven't seen it yet. They ask EUR 3900 EUR (about USD 4600). Max lenght...
7 comments posted 20yrs
posted by muellernick
7 comments posted 20yrs posted by muellernick

OT- Obituary (some here may have known him)

Hi all, My Grandfather, Fred Fowler Sr., passed this last Tuesday AM. He loved machining & engineering, even made his o...
8 comments posted 20yrs
posted by fred
8 comments posted 20yrs posted by fred

Sheldon lathe question

How are the older sheldon lathes? I don't see a whole lot on ebay so getting an idea of the going rate is hard. I am loo...
5 comments posted 20yrs
posted by wayneREMOVETHIS
5 comments posted 20yrs posted by wayneREMOVETHIS

OT Generator Question

Does any damage occur if you overload a brushless generator and the engine stalls out? Do you need to re-energize the g...
3 comments posted 20yrs
posted by GeoLane_NOSPAM_
3 comments posted 20yrs posted by GeoLane_NOSPAM_

SBC!!!(with disgust!!!!)

Having dropped my connection in Feb of 2005, and started again in October of 2005, it sure hasn't taken SBC very long t...
31 comments posted 20yrs
posted by richard
31 comments posted 20yrs posted by richard

FOOT SHEAR

If a foot shear can shear 18 ga. steel, is there any way to determine what max. ga. al. it can shear of the same x/y di...
5 comments posted 20yrs
posted by finalact
5 comments posted 20yrs posted by finalact

OT: Happy Saturnalia (Winter Solstice ritual)

Here ya go. An alternative to the regular xmas video: http://www.jingleshells.com/flash_content/flash_content.html (Att...
3 comments posted 20yrs
posted by ljaques
3 comments posted 20yrs posted by ljaques

"Universal" TIG electrodes (tungstens)?

Looking at some online TIG consumable sellers web sites it seems I can buy TIG tungstens alloyed to make a universal el...
9 comments posted 20yrs
posted by chris
9 comments posted 20yrs posted by chris