⏣ General Metalworking

30777 Threads Posts
to

Introduction & question

Hi all, I'm new to the list but have read some of the digests. I picked up my first metal lathe last week & have many q...
2 comments posted 21yrs
posted by b.d.brown
2 comments posted 21yrs posted by b.d.brown

can this small TIG machine run hardwire?

can this small TIG machine run hardwire? (spool-gun) http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=91...
6 comments posted 21yrs
posted by ralloha2
6 comments posted 21yrs posted by ralloha2

OT-Amazing Woodcarvings - (Some metal content)

There's gotta be some metal under the hood of that Ferrari... This guy's GOOD! http://home.comcast.net/~jwisnia18/temp/c...
0 comments posted 21yrs
posted by jwisnia
0 comments posted 21yrs posted by jwisnia

tom(nospam)@ohiobrush

Tom Three messages no reply. I sent an inquiry about prices on your brushes so I might be able to quit using the China...
7 comments posted 21yrs
posted by 141
7 comments posted 21yrs posted by 141

model steam engine question

Got a Stuart vertical engine, model 10v, piped up to a PM Research boiler. The engine runs great 5lbs of air but will n...
9 comments posted 21yrs
posted by jwolgamuth
9 comments posted 21yrs posted by jwolgamuth

Some taps on eBay

Good quality taps on eBay. All are new and were never used. All come with red plastic protective sleeves. If you buy mo...
0 comments posted 21yrs
posted by jwfilion
0 comments posted 21yrs posted by jwfilion

Phase II angle plate slot CtoC dimensions

Looking to buy a couple of the Phase II 5x6" swival angle plates that ENCO is selling as P/N 418-4180. They are not goi...
0 comments posted 21yrs
posted by rbce2003
0 comments posted 21yrs posted by rbce2003

Cutting heating costs and water heater

I am interested in building a waste oil wood burner or something that would but my propane usage. I dont have a basemen...
7 comments posted 21yrs
posted by stryped
7 comments posted 21yrs posted by stryped

Auction coming up

Lots of machines and I would guess tons of tooling!! Rockford, Illinois next week. Check out the auctioneers website. ht...
4 comments posted 21yrs
posted by tomwait308landmine
4 comments posted 21yrs posted by tomwait308landmine

bench top height question for mini-mill

Hey, I am trying to determine a good height for my workbench for a mini-mill. I am getting one of the cheap Chinese one...
42 comments posted 21yrs
posted by onetoncrewcab
42 comments posted 21yrs posted by onetoncrewcab

Suggestions for underwater camera housing

I make something for use in swimming pools out of plastic plumbing pipe, but a fellow I was talking to last night had a...
9 comments posted 21yrs
posted by jtaylor
9 comments posted 21yrs posted by jtaylor

Transparent Aluminum?

Bullet resistant too... great for sunglasses sold on eBay. http://www.af.mil/news/story.asp?id=123012131 Air Force test...
47 comments posted 21yrs
posted by granpawii
47 comments posted 21yrs posted by granpawii

OT - air compressor

I have a home brew air compressor which uses an electric motor. It uses a pressure switch to stop the motor when the ta...
6 comments posted 21yrs
posted by stone75
6 comments posted 21yrs posted by stone75

Does anyone recognize this article?

I've always wanted to make my own scope and have a couple of designs, but this article: http://cgi.ebay.com/ws/eBayISAP...
23 comments posted 21yrs
posted by jbm
23 comments posted 21yrs posted by jbm