⏣ General Metalworking

30777 Threads Posts
to

Making magnesium strips with a lathe?

I recently bought a piece of magnesium rod 2" thick by 6" long. I tried making very few magnesium strips using my lathe...
2 comments posted 21yrs
posted by ignoramus6767
2 comments posted 21yrs posted by ignoramus6767

Bushog repair question

I brought my dad's older bushog home to try to fix it. The metal the hoghead mounts to were broken. I am going to try t...
4 comments posted 21yrs
posted by stryped
4 comments posted 21yrs posted by stryped

Bernzomatic welder Question

I see these setups at Home Depot for about $50. All I am looking for is something to weld wrought iron fences or railin...
6 comments posted 21yrs
posted by arthur.moore
6 comments posted 21yrs posted by arthur.moore

Working brass rod

I'm trying to make what's essentially an eye bolt out of 1/4" diameter brass rod. My first inclination was to simply he...
3 comments posted 21yrs
posted by rookiemacine
3 comments posted 21yrs posted by rookiemacine

Wanted=-Pressure washer hose and gun

Im assembling a pressure washer from an old Dakota heated pressure washer setup that Jerry Martes found for me, and am...
0 comments posted 21yrs
posted by gunner
0 comments posted 21yrs posted by gunner

How To Adjust Quill Lock on Bridgeport J-head?

The subject says it all. Is this a difficult adjustment? I'd be forever greatful if someone could offer some help. Thank...
14 comments posted 21yrs
posted by none
14 comments posted 21yrs posted by none

Mighty Mag Magnetic Base Modifications?

It seems to have no flat surfaces, other that the magnetic sticky side. It seems to be made of Aluminum, epoxy, and som...
11 comments posted 21yrs
posted by c.magnuson
11 comments posted 21yrs posted by c.magnuson

painted/galvanized steel contact areas

The boat trailer guide base that I made today is made of mild steel that I painted with rustoleum (thanks to advice rec...
1 comments posted 21yrs
posted by ignoramus26696
1 comments posted 21yrs posted by ignoramus26696

South Bend 2CW Lathe

I have located a SouthBend 2CW 16x?? (the bed is 6' but actual center to center abt 3') lathe in decent shape for a WWI...
0 comments posted 21yrs
posted by radio.service
0 comments posted 21yrs posted by radio.service

Sheldon/Vernon Horizontal Mill

Hey Folks, I just purchased a Sheldon/Vernon horizontal mill (http://www.lathes.co.uk/sheldon/page8.html) and I need th...
14 comments posted 21yrs
posted by 59vw
14 comments posted 21yrs posted by 59vw

FS: Flat bed/Car Hauler Trailer

6'-6" wide by 16' long diamond plate steel deck, tandem axle, with electric brakes on one axle. Ramps stow under the de...
0 comments posted 21yrs
posted by escarcegaNOSPAM
0 comments posted 21yrs posted by escarcegaNOSPAM

Differences between CAT40 and NT40 tapers?

Are there any differences between NT40 and CAT40 spindle tapers? I've also seen reference to 40 National Taper, 40 Nati...
15 comments posted 21yrs
posted by no-spam
15 comments posted 21yrs posted by no-spam

How much are metal PIPES weakened by THREADS?

I made this boat trailer guide base: http://igor.chudov.com/projects/Trailer-Guide/ To it, I planned to attach a short...
6 comments posted 21yrs
posted by ignoramus26696
6 comments posted 21yrs posted by ignoramus26696

mistery bench grinder

I just bought an old and heavy duty looking grinder. It's probably 50 y.o., very heavy and runs pretty smooth. Arbor is...
4 comments posted 21yrs
posted by alexkuzn
4 comments posted 21yrs posted by alexkuzn