⏣ General Metalworking

30777 Threads Posts
to

What is it? LXVI

Just posted another set of photos: http://puzzlephotos.blogspot.com/ Rob
21 comments posted 21yrs
posted by rhvp67
21 comments posted 21yrs posted by rhvp67

Atlas Lathe Timken Bearings

I have an Atlas metal lathe w/ 10" swing -- quick change gearing -- 48" bed, etc. Timken bearings are installed. PROBLE...
4 comments posted 21yrs
posted by nauticalguysfo
4 comments posted 21yrs posted by nauticalguysfo

O/A torches

Hello. I bought a used arc welder today which included a box with assorted stuff. One of the things in the box was Vict...
5 comments posted 21yrs
posted by alamm001
5 comments posted 21yrs posted by alamm001

lathe belt replacement (again?)

I know it has been discussed but I haven't found an exact answer in older messages. I bought a used 13" Taiwan lathe. I...
9 comments posted 21yrs
posted by notreally
9 comments posted 21yrs posted by notreally

Mag switch update

Thanks for all the replies to my magnetic switch query. I finally got time to completely disassemble it clean everythin...
5 comments posted 21yrs
posted by andrewV
5 comments posted 21yrs posted by andrewV

New low cost DRO

Check out this site- http://forums.delphiforums.com/MadeinUSA/messages/?msg=8.1 Specs look good and price is real good
10 comments posted 21yrs
posted by Edshomeshop
10 comments posted 21yrs posted by Edshomeshop

Source for 10mm 303 Stainless Steel rod stock?

Hi, I'm looking for a source for 10mm 303 Stainless Steel Rod. Anyone have a US or Canadian Supplier? Thanks, - Mike -
5 comments posted 21yrs
posted by mhaaland
5 comments posted 21yrs posted by mhaaland

Info on Cleveland Mill?

Ran across this locally. Anyone have one or know anything about it? This guy apparently keeps his stuff in good repair...
0 comments posted 21yrs
posted by rex
0 comments posted 21yrs posted by rex

8 AWG current capacity

I have found several hundred feet of 8 AWG wire that I would like to use to bring electricity to my shop that is 200' f...
22 comments posted 21yrs
posted by sbaer
22 comments posted 21yrs posted by sbaer

VFD recommendations sought

Another poster mentioned driving his drill press from a Variable Speed Drive (VFD) to slow things down to a speed suita...
25 comments posted 21yrs
posted by JoeGwinn
25 comments posted 21yrs posted by JoeGwinn

Taig Mill Spindle Removal

I wanted to remove the spindle and bearings from the headstock on my taig mill. I removed the pulley, top nut, and smal...
2 comments posted 21yrs
posted by terry.gaston
2 comments posted 21yrs posted by terry.gaston

Bolting Lathe to Concrete Floor

I have a 13x40 Sheldon Lathe and am getting ready to get it set up properly. It weighs about 1500lbs and has 4 leveling...
17 comments posted 21yrs
posted by Sierevello
17 comments posted 21yrs posted by Sierevello

Jet model 836

Anyone know the quality of this Jet mill, seems that Jet is a well made product for the price. I also looked at the tab...
1 comments posted 21yrs
posted by mjc117
1 comments posted 21yrs posted by mjc117

using a VW type 1 engine for a go-kart

Greetings all, I recently acquired a 67 Type I VW engine for free, and just happened to be planning on building a off r...
17 comments posted 21yrs
posted by athos76
17 comments posted 21yrs posted by athos76

need help hooking up three phase mill

I bought an Index mill which has a 220/440 three phase motor on it. It also has a "ThreePhaser Model 1000" converter bo...
19 comments posted 21yrs
posted by 9ekdu
19 comments posted 21yrs posted by 9ekdu