⏣ General Metalworking

30778 Threads Posts
to

Removing zinc/cadmium plating?

Is there an easy way to remove zinc and/or cadmium plating without affecting the steel underneath? Thanks,
17 comments posted 21yrs
posted by zenadsl6186
17 comments posted 21yrs posted by zenadsl6186

OT-Hunter Thompson takes Ultimate Road Trip

It's better to be a red person in a blue state than a blue person in a red state. As a red person, if your blue neighbo...
14 comments posted 21yrs
posted by gunner
14 comments posted 21yrs posted by gunner

I need to make a muffler for my furnace vent

I have a boiler in my house which is vented to the side at ground level (the machinery room is below grade). The vent a...
22 comments posted 21yrs
posted by grant
22 comments posted 21yrs posted by grant

Followup questions: Hydraulics for logsplitter

Once again, many thanks for the very helpful information you have given me on hydraulics in general, and applying them...
4 comments posted 21yrs
posted by ahw
4 comments posted 21yrs posted by ahw

Ratings on plasma cutters?

Does anybody have a feel for how "optimistic" or overstated some of the ratings for some of the import plasma cutters i...
8 comments posted 21yrs
posted by rpseguin
8 comments posted 21yrs posted by rpseguin

very long linear rails and screws

I am planning to build a very large CNC plasma cutting table for cutting plates of 6000x2000 mm metric, so about 20' by...
8 comments posted 21yrs
posted by someone
8 comments posted 21yrs posted by someone

transformer sizing

Is there a general rule of thumb for how big a transformer will handle a certain size motor. I need to step up 220 volt...
16 comments posted 21yrs
posted by karltownsend.NOT
16 comments posted 21yrs posted by karltownsend.NOT

A Pasta Machine is NOT a Rolling Mill

Thanks for all the suggestions regarding my need for a rolling mill. I should be able to get what I need for less than...
6 comments posted 21yrs
posted by llhote
6 comments posted 21yrs posted by llhote

"Top 10" DRO

Does anyone have experience with the "Top 10" DROs being sold on ebay? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ca...
3 comments posted 21yrs
posted by dcstaber
3 comments posted 21yrs posted by dcstaber

Durable Downspouts

Hello, It looks like I have to attempt a small metalworking project. I own an apartment complex out in Fresno, CA. Last...
26 comments posted 21yrs
posted by jerry
26 comments posted 21yrs posted by jerry

Should I ebay a Starret #199 level? Bandsaw?

I have this Starrett #199 master precission level that I have no use for. There always seems to be a few on Ebay and th...
7 comments posted 21yrs
posted by tom(nospam)
7 comments posted 21yrs posted by tom(nospam)

What model welder is this?

Hello everyone. I've spent many,many months now, trying to find one of those elusive "$50 - $100" 220v buzz boxes aroun...
10 comments posted 21yrs
posted by alamm001
10 comments posted 21yrs posted by alamm001

Painting Antique Power Hacksaw

I am rebuilding a 14" power hacksaw made by Champion Blower and Forge. I figure that the saw was made pre WWII (20's-30...
3 comments posted 21yrs
posted by dpidwerbecki
3 comments posted 21yrs posted by dpidwerbecki

unscrew fitting or cut/thread black iron pipe

I want to put in a tee for a new drip line and flexible gas connector when I replace my water heater. It is currently c...
2 comments posted 21yrs
posted by rald
2 comments posted 21yrs posted by rald