⏣ General Metalworking

30778 Threads Posts
to

Sheet metal work - UK

I am looking for someone/a firm to make up a simple prototype for me from mild steel sheet. It's basically a box, invol...
1 comments posted 22yrs
posted by NOTsomeone
1 comments posted 22yrs posted by NOTsomeone

Cut-out paterns

Hello I am looking for sheep and cow paterns for a project. I would like to make some steel cut-out for a birthday gift...
5 comments posted 22yrs
posted by iti81nq02
5 comments posted 22yrs posted by iti81nq02

chuck key

What number chuck key do I need for a 1/2" cap. chuck with a 15/64" pilot? Is there a chart somewhere that has the dimen...
8 comments posted 22yrs
posted by nsmith001
8 comments posted 22yrs posted by nsmith001

simple way to bend sheet metal?

Hi all, I need to bench a 4x10 piece of .032 aluminum in two points along its length, both at 90 degree angles. I've ne...
5 comments posted 22yrs
posted by u9526
5 comments posted 22yrs posted by u9526

What is Semi-steel?

Amongst my small collection of silversmithing tools is a Dixon t-stake with the words 'semi steel' cast into the base....
17 comments posted 22yrs
posted by richmccar
17 comments posted 22yrs posted by richmccar

Hydraulic Pump for Press

I have an SPX Team Cylinder rated at 15 tons for a press. I need to figure out what type of pump I need to get the most...
4 comments posted 22yrs
posted by Sierevello
4 comments posted 22yrs posted by Sierevello

OT forklift carb identity

I have an older Datsun forklift with a Nissan D11 engine in it. 1138 cc. The carburetor is a 2 barrel with a factory bl...
3 comments posted 22yrs
posted by occupantr
3 comments posted 22yrs posted by occupantr

FS: Hossfeld Type Bender and 1-1/4" Die Set

I built a tubing bender based on drawings that someone made of a Hossfeld #2 bender. I bought a set of 1-1/4" Genuine H...
0 comments posted 22yrs
posted by escarcegaNOSPAM
0 comments posted 22yrs posted by escarcegaNOSPAM

how to join aluminum edges

Hi all, I'm building a truck shell (also called a cap, topper, or canopy) to put on the back of my truck to replace tha...
39 comments posted 22yrs
posted by u9526
39 comments posted 22yrs posted by u9526

OT - Anyone know Bob Richardson?

I've been searching for an old friend named Bob Richardson, who I think is the same one who popped in here back in '95,...
0 comments posted 22yrs
posted by huntres23
0 comments posted 22yrs posted by huntres23

Anyone have a exploded diagram of a Rem Mod 14?

I was given a rather nice old Remington Mod 14 in .30 Rem this week, but it has a jamming problem where the slide actio...
11 comments posted 22yrs
posted by gunner
11 comments posted 22yrs posted by gunner

Best for Aluminum FS: Cobramatic Wire Feeder

MIG WIRE FEEDER COBRAMATIC I have 2 Cobramatic MIG wire feeders and I am in Ottawa, Canada. These are Professional Wire...
1 comments posted 22yrs
posted by southshallfall
1 comments posted 22yrs posted by southshallfall

Enco vs Di-acro?

I'm looking at buying some basic sheet metal equipment, namely a shear, a finger brake, and a corner notcher. There is...
13 comments posted 22yrs
posted by DaveNugent
13 comments posted 22yrs posted by DaveNugent

I moved my mill !!

I bought an old 9x42 Maxmill earlier this week. The tow truck dropped it off near the door. Tonight I used my Harbor Fr...
9 comments posted 22yrs
posted by no
9 comments posted 22yrs posted by no