⏣ General Metalworking

30779 Threads Posts
to

Sheet Metal Cone Software

Hi folks... Recently had to make a sheetmetal cone and found a great piece of freeware in searching the Net. If you nee...
3 comments posted 22yrs
posted by surftom
3 comments posted 22yrs posted by surftom

New project in the works

I am finally getting around to making a bandsaw, floor model vertical type mainly for cutting metals, and occasional li...
5 comments posted 22yrs
posted by chipmkr
5 comments posted 22yrs posted by chipmkr

Lathe setup question

Hi, I have just purchased a new (to me) lathe a Denford Viceroy 280. It's installed in it's new home and I have set it...
7 comments posted 22yrs
posted by chris.cain
7 comments posted 22yrs posted by chris.cain

BECKER mill (info needeed)

Hi all, I'm new on this group, motorbike enthusiast, member of some mailing list like "mc-chassis-design" talking about...
1 comments posted 22yrs
posted by stephane.troncard
1 comments posted 22yrs posted by stephane.troncard

sawzall or reciprocating saw tips?

I bought this cheap version of "sawzall" but it's a craftsman one for like $60. Perhaps it's a craftsman one instead of...
11 comments posted 22yrs
posted by jeremy_ho
11 comments posted 22yrs posted by jeremy_ho

Using Brass Round to Lap Chuck Jaws

I was reading up on lapping chuck jaws and came across the thread about using a brass bar and valve lapping compound to...
8 comments posted 22yrs
posted by Sierevello
8 comments posted 22yrs posted by Sierevello

What metal holds eraser in the pencil?

There is a short metal tube sleeve of soft metal that holds eraser in the pencil. Does anyone know what exactly that met...
18 comments posted 22yrs
posted by alexkuzn
18 comments posted 22yrs posted by alexkuzn

mystery shaper

I looked at a shaper today that was advertised in the local paper. The owner bought it at a school auction several year...
5 comments posted 22yrs
posted by lsume
5 comments posted 22yrs posted by lsume

Identifying a "Utility Lathe"

I just recieved a "Utility Lathe" and that's all that it has for ID on the casting... and would like to know more about...
0 comments posted 22yrs
posted by frnkgmbk
0 comments posted 22yrs posted by frnkgmbk

HELP: Removing Toolchest Drawer

I have an old Snap-On toolchest (bought it very used around 1980). It has four full width drawers. One of the drawers w...
3 comments posted 22yrs
posted by no
3 comments posted 22yrs posted by no

Tool bargain followup

A few of you may remember the question I posted a while back about hand tool bargains; even fewer of you might care. An...
4 comments posted 22yrs
posted by bryan
4 comments posted 22yrs posted by bryan

DATSUN ROADSTER Resurection Update

Work is progressing on my Datsun Roadster; rear-ended by an F 250. See my homepage link, and follow the Datsun links to...
3 comments posted 22yrs
posted by jasonXrnorth
3 comments posted 22yrs posted by jasonXrnorth

ADV: 15% Off Geo-Matic Complete this week only!

My apologies in advance to those who feel this message is off-topic or in poor taste! For one week only, register Geo-M...
0 comments posted 22yrs
posted by ccastiglia
0 comments posted 22yrs posted by ccastiglia

Welding table?

I was browsing the group but couldn´t find any link to a picture or drawning of a welding table. Any suggestions how to...
21 comments posted 22yrs
posted by sofar
21 comments posted 22yrs posted by sofar

Has anyone tried this room-temp Black Oxide?

Hi All, I've done lots of reading on black oxiding steel, and the general concensus is that the room-temp products are...
4 comments posted 22yrs
posted by rlhead
4 comments posted 22yrs posted by rlhead