⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Prop 65

On some welding rod "This product contains chemicals known to the State of California to cause cancer and birth defects...
0 comments posted 15yrs
posted by tim
0 comments posted 15yrs posted by tim

Son's BBQ Pit Project

My middle son Ben did his 2nd project with the Millermatic 180 I got him. He's going to Texas State U. so doesn't have...
19 comments posted 15yrs
posted by keillorp135
19 comments posted 15yrs posted by keillorp135

OT sorry I couldn't resist

Two little old ladies were sitting on a park bench outside the local town hall where a flower show was in progress. The...
1 comments posted 15yrs
posted by gmasterman
1 comments posted 15yrs posted by gmasterman

Maybe OT: Save fuel with a setback thermostat?

If the fact that my furnace is metal qualifies for "metal content", then let it be so. If not, then this post is off to...
23 comments posted 15yrs
posted by spaco
23 comments posted 15yrs posted by spaco

G-codes past RS-274 a waste?

I'm beginning to think that the only reason why manufactures add complex cycles outside the RS-274 basic list is to sav...
10 comments posted 15yrs
posted by lloydspinsidemindspring.com
10 comments posted 15yrs posted by lloydspinsidemindspring.com

Rearview mirror glue

I want to glue a piece of steel to my truck's windshield, with some threaded holes so I can attach anything to it (such...
16 comments posted 15yrs
posted by ignoramus4371
16 comments posted 15yrs posted by ignoramus4371

Gloat Electric Motor

Well that is, if it is fixable. 7.5 HP Baldor Industrial Motor 110 to 440V 1725 rpm free ! The shaft won't turn all the...
20 comments posted 15yrs
posted by SW
20 comments posted 15yrs posted by SW

Inspiron 14

I absolutely love my Inspiron 14. I always research products before I purchase them. This product had very high ratings...
0 comments posted 15yrs
posted by aamar22
0 comments posted 15yrs posted by aamar22

What is it? Weekend Edition 10

39. Someone sent this to me a week or two ago, you can test your memory on it since it was posted on the site over thre...
23 comments posted 15yrs
posted by rhvp65
23 comments posted 15yrs posted by rhvp65

compressor tank repair

OK, so I got a deal - Like new 60-gallon Kobalt compressor for $125 on CL. He said it had a hole in the tank, but he co...
36 comments posted 15yrs
posted by burkheimer
36 comments posted 15yrs posted by burkheimer

Way skirts question for Iggy

Ig, the other day, I replace the front and rear way covers on my r2e4, because they were cracked. I selected 1/16" neop...
9 comments posted 15yrs
posted by lloydspinsidemindspring.com
9 comments posted 15yrs posted by lloydspinsidemindspring.com

MSC's web site

Tried the new seach, still sucks as much as the old one. Placed an order for 3 things.... 2 items 1 day shipment from P...
0 comments posted 15yrs
posted by rbraun333
0 comments posted 15yrs posted by rbraun333

How NOT to remove a lathe chuck

http://www.liveleak.com/view?i=d27_1291395628 Could have ended up much worse. How many things did they do wrong?
27 comments posted 15yrs
posted by anorton
27 comments posted 15yrs posted by anorton

FF - "Machinist's Workshop"

Free - 7 issues "Machinist's Workshop" (June/July 2009 thru June/July 2010). MW is a lower level than Home Shop Machini...
0 comments posted 15yrs
posted by bobengelhardt
0 comments posted 15yrs posted by bobengelhardt

Unimat db 200 indexing attachment question

I bought one of these things at an auction recently but there is no indexing plate or an obvious way that you might att...
10 comments posted 15yrs
posted by doc
10 comments posted 15yrs posted by doc