⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30775 Threads Posts
to

Worth reading in ⏣ General Metalworking

New User - Dalton T-L No 292

Hello - I own a Dalton T-L. The stamped letters and numbers on the right end of the rear way appear to be T-L NO 202 or...
5 comments posted 5yrs
posted by gparment
5 comments posted 5yrs posted by gparment

Charging NiMH battery pack

I bought a $35 pair of replacement battery packs for my 14.4V DeWalt drill that contain NiMH instead of NiCad cells lik...
26 comments posted 5yrs
posted by muratlanne
26 comments posted 5yrs posted by muratlanne

where's all the political slagging-match gone?!

Hi all I always thought of the political slagging matches on here - the "off-topic" posts - were a nuisance - "signal"...
5 comments posted 5yrs
posted by null
5 comments posted 5yrs posted by null

Chinese steel ?

Some may recall a few months ago while I was building the rooster weather vane that I had porosity problems while TIG w...
5 comments posted 5yrs
posted by Snag_one
5 comments posted 5yrs posted by Snag_one

Sheet metal bending question....

Just bought an inexpensive baking pan hoping it would fit an old toaster oven. Only $1, and it seemed decently made so...
5 comments posted 5yrs
posted by bp
5 comments posted 5yrs posted by bp

load for steel pipe

I am going to be hanging cast iron skillets from a 1" x 5' black steel pipe (see link from Hope Depot below). It will b...
9 comments posted 5yrs
posted by londonriver3
9 comments posted 5yrs posted by londonriver3

Small pieces of steel Sheet.

I have a project I am working on that could use a fair number of small pieces of steel sheet. Mild steel is just fine....
21 comments posted 5yrs
posted by none
21 comments posted 5yrs posted by none

general purpose fill rod for OA

Is RG45 the most generic/general purpose fill rod that can be used on boring low-carbon steels like A36 or rebar? I'd b...
1 comments posted 5yrs
posted by presence
1 comments posted 5yrs posted by presence

Water For Coolant

At no time since I have started using water soluble coolant have I used tap water. I am on a private well here and have...
3 comments posted 5yrs
posted by none
3 comments posted 5yrs posted by none

aluminm bearing for pivot?

I am making a swing-away bike carrier to fit in trailer hitch reciever. With everything shut down I need to use what I...
4 comments posted 5yrs
posted by clare
4 comments posted 5yrs posted by clare

Custom seals to keep debris out of linear bearings?

Plastic filament won't work for bearings here, because the bearings must move freely on rods even when twisting pressur...
3 comments posted 5yrs
posted by always.look
3 comments posted 5yrs posted by always.look

pock mark in cast iron skillet

Got a I suspect new-ish Lodge cast iron skillet with a small void, maybe 1/16" in diamter. What's the laziest way to fi...
13 comments posted 5yrs
posted by presence
13 comments posted 5yrs posted by presence

OT: Plastic Igus Drylin bearings can be cut?

In case anybody knows... https://www.amazon.com/gp/product/B071RSDYW4/ref=ox_sc_act_title_2?psc=1&m=ATVPDKIKX0DER Can t...
10 comments posted 5yrs
posted by always.look
10 comments posted 5yrs posted by always.look

building trailer axles

I am tring to replace old mobile home axle with mismatched barings. Looks like my best choice is to customer make them....
0 comments posted 5yrs
posted by 0f8503901d844703eea1acecb7a4938a_2737
0 comments posted 5yrs posted by 0f8503901d844703eea1acecb7a4938a_2737