Latest threads in ⏣ General Metalworkingshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Anyone know about Bosch quickchange compact drill drivers?
Specifically, the PS21-2A. The item I just bought does not hold all of my quickchange drill bits properly. At the same time, my Bosch I-Driver holds the same bits perfectly. I really really like this...
9
|
13 years ago
|
9 | |
|
|
You have come a long way
Remember that a commercial about 'You came a long way baby' once upon a time. Oh yes, 'Virginia Slims'. Remember back in the past when Iggy asked some rather *interesting* questions and some of us...
8
|
13 years ago
|
8 | |
|
|
underwater metal working in the gulf
for those interested, the Skandi Neptune video feed is showing what's happening as BP replaces the cap on the blowout preventer and takes other action - it's pretty interesting some times, boring at...
8
|
13 years ago
|
8 | |
|
|
Rust stains on fiberglass-what works?
Pulled the 20 yr old water heater on my boat. It was incredibly rusty and corroded. Underneath where it was mounted, the fiberglass deck is badly stained with rust. Checked CLR on Epinions-just what I...
11
|
13 years ago
|
11 | |
|
|
Surface grinder for sale
relation to seller One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of...
3
|
13 years ago
|
3 | |
|
|
Anvils for sale
relation to seller One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of...
1
|
13 years ago
|
1 | |
|
|
Atlas/Craftsman Change gears
relation to seller One could not be a successful Leftwinger without realizing that, in contrast to the popular conception supported by newspapers and mothers of Leftwingers, a goodly number of...
—
|
13 years ago
|
— | |
|
|
The mill is creeeeepy
... Because it "creeps". I have only one axis (x) wired right now. When the drive is powered on, but with no input signal, the table imperceptibly slowly creeps. I only noticed it because some tools...
30
|
13 years ago
|
30 | |
|
|
New Virtual 'Nam Wall
Someone spent a lot of time on this and it is truly remarkable, take a look........................... Someone sent me the link below which is a virtual wall of all those lost during the Viet Nam war...
8
|
13 years ago
|
8 | |
|
|
Using a spring to bend pipe?
Is there anything to know besides sticking the pipe through the spring and bending it? Thanks.
12
|
13 years ago
|
12 | |
|
|
Steel Conduit Question
OK, I have now established proper metal content. The issue is more of an electrical code issue, and I'm hoping the wealth of knowledge of the usual suspects can help me out. My basement shop needs...
56
|
13 years ago
|
56 | |
|
|
The fragrance of tools
We all know about the Harbor Freight stink, of Cosmoline and cheap rubber and other suchlike. Well I had a rather different experience today. My old Stanley ratchet (not Yankee) screwdriver walked off...
3
|
13 years ago
|
3 | |
|
|
unknown collet need ID help
I have a nice set of small collets that I cannot match up on any of the collet charts. Looks like a miniature R8. Here's the specs 3.00" OA Length .500"bearing/shaft diameter .675 max diameter at...
11
|
13 years ago
|
11 | |
|
|
Gear question
Want special lathe tool form cutter to cut gears. After an extend lapse, I want to complete a set of change gears for my EMCO Compact 10 lathe. have hand ground the gear tooth profile and this works...
10
|
13 years ago
|
10 | |
|
|
OT-DA prossecutes victim
WHEAT RIDGE, Colo. - Admitted thieves are going free, while an elderly Wheat Ridge man is facing the possibility of spending the rest of his life behind bars, all, he says, for trying to defend his...
8
|
13 years ago
|
8 |