Latest threads in ⏣ General Metalworkingshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Mathematical mm/inch and triangle oddities
A couple of things I've noticed over the years: 19mm is really really close to 3/4". It's actually 0.748 inches but I'm not sure any equipment I work with has the bolt heads cut to better than two...
6
|
16 years ago
|
6 | |
|
Jo block preservitive
All Got a set of economy Jo blocks for xmass, in a nice wooden box with what appears to be a plastic welled liner. Anyway, each block came wrapped in the typical greasy paper. Past experience has...
21
|
16 years ago
|
21 | |
|
Olde Books?
1
|
16 years ago
|
1 | |
|
OT Digital camera mod
I know this is WAY OT but I need some clues to get started. I want to use a digital camera as a security camera. The problem is that all digital cameras that I know about turn themselves off...
62
|
16 years ago
|
62 | |
|
MAN SPENDS CHRISTMAS EVE UPSIDE DOWN IN SEPTIC TANK
The 77-year-old man spent part of Christmas Eve stuck upside down in the opening of his septic tank, with his head inside and his feet kicking in the air above. "It wasn't good, I'll tell you what,"...
6
|
16 years ago
|
6 | |
|
DC Motor Controller "Inhibit Circuit"?
I'm finally getting around to wiring up my Beel Inc Motor Controller. (ebay id beelindustrial) Basically similar to a KBIC-125. The kit I have has a forward/break/ reverse switch. The wiring diagram...
4
|
16 years ago
|
4 | |
|
WTB - THE WORST VICTOR WELDING TIP YOU GOT
I'm putting together my Gopher Getter, and have come down to the realization that a welding tip that has been cut would be the quickest easiest way to channel mixed gas from the mixing body. If you...
—
|
16 years ago
|
— | |
|
Back to Carbide vs Diamond
The following tool is for sale at the Harbor. Item No. 46727 (Sorry but I am failing at pasting a workable hyperlink to the item. When I try to click my own pasted hyperlink, it comes back "item not...
7
|
16 years ago
|
7 | |
|
Extracting broken bolt / screw
Hi; Often I need to extract broken bolts / screws and am thinking about picking up some left handed drill bits. Usually I have to extract broken steel bolts and screws from aluminum heads and...
46
|
16 years ago
|
46 | |
|
video of my lathe
GLOAT I see Camsoft just put my CHNC lathe up on their web site. Likely too much trouble for most because you'll have to register and log in to see it. Scroll down page to CHNC 's me talking. Ever...
11
|
16 years ago
|
11 | |
|
fa - nice new right angle drive gear assembly
several folks on the NG have discussed a need for these from time to time - I have two to offer - here's a link so you can see what they are: are older, but new in box, link to page with specs, etc is...
2
|
16 years ago
|
2 | |
|
DC motor drive with voltage boost
What DC drive controller will produce more than 90vdc from 115vac?
5
|
16 years ago
|
5 | |
|
ToolUnknown Help
Any thoughts would be appreciated. It's made by Miller Falls and says "#381 3 1/2 The pics are in the drop box:
7
|
16 years ago
|
7 | |
|
Tapered bearing race install
I need to install two tapered bearing races in a steering head. First off let me say that with a few exceptions I hate dealing with pressed in parts. Last time I had to do this I failed miserably and...
19
|
16 years ago
|
19 | |
|
Nice Lathe for the Consumate Hobbist
Do you think that I could lift it into my truck with my truck crane? i
18
|
16 years ago
|
18 |