⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

OT where to buy abuse resistant US flags

This is for my trailer. It is next to impossible to back up at night without flags in the back. I just do not see it. d...
5 comments posted 19yrs
posted by ignoramus1197
5 comments posted 19yrs posted by ignoramus1197

FS -- EDM electrode blanks

Came across a moderately large quantity of new EDM electrode blanks. (my guess is 150 lbs, but I will know for sure tom...
8 comments posted 19yrs
posted by ignoramus1197
8 comments posted 19yrs posted by ignoramus1197

OT: CO2 evaporator or vaporizer

I'm looking for a way to vaporize 20 lbs/hour of liquid CO2 from a refrigerated bulk tank and deliver the gas at about...
26 comments posted 19yrs
posted by kinch
26 comments posted 19yrs posted by kinch

Worm gear fabrication help please

Hello to all. I just found this group and I'm hoping someone can help me. I have a worm gear with the teeth on one side...
10 comments posted 19yrs
posted by <vanbar6
10 comments posted 19yrs posted by <vanbar6

Easter Eggs Suck! - Slightly OT

Lots of tools used in getting this done though.... My wife (a teacher) recently asked me to "blow out" 6 dozen eggs(!)...
1 comments posted 19yrs
posted by surftom
1 comments posted 19yrs posted by surftom

Any blast furnaces in Silicon Valley?

Im looking to try my hand at casting some iron pulleys and flywheels, however i can¹t build a small iron foundry at my...
11 comments posted 19yrs
posted by tomswift
11 comments posted 19yrs posted by tomswift

What is it? CLXIV

http://puzzlephotos.blogspot.com/ Rob
16 comments posted 19yrs
posted by rhvp67
16 comments posted 19yrs posted by rhvp67

Maglie LED Conversion Failure & Repair

A while back I got a regular 2AA Maglite to use at work. Then I stuck in a TerraLUX Luxeon upgrade kit. Very swanky, I...
2 comments posted 19yrs
posted by DoNotSpamthegoat4
2 comments posted 19yrs posted by DoNotSpamthegoat4

Machine tool accessories for sale in Portland

I'll be at the Portland Auto Swap Meet next week with several hundred pounds of cutting tool and machine tool accessori...
24 comments posted 19yrs
posted by CATRUCKMAN
24 comments posted 19yrs posted by CATRUCKMAN

FYI: Homer lists their sale locations online now

In the past the only way to find out when Homier was heading to your area was by subscribing to their notifications. I...
1 comments posted 19yrs
posted by tooladdict
1 comments posted 19yrs posted by tooladdict

Clever lockbox design needed

Hi people, OK, the opener proceeds with much excitement and I am now approaching the "other" stuff department. Prior to...
10 comments posted 19yrs
posted by Jenny3kids
10 comments posted 19yrs posted by Jenny3kids

HF pipe bending dies

I have an inexpensive pipe bender. Its dies are about a quarter of a circle; in other words are about 90 degrees. I nee...
7 comments posted 19yrs
posted by grant
7 comments posted 19yrs posted by grant

Flux this is difficult!

How's that for a subject line? nooB Ben back with another fundamental question. I'm having consistent issues with picki...
2 comments posted 19yrs
posted by nospam
2 comments posted 19yrs posted by nospam

Buffalo drill press motor

I have been the recipient of an old Buffalo drill press. The motor is burned up and needs to be replaced. Any suggestion...
10 comments posted 19yrs
posted by purphektdeletethis
10 comments posted 19yrs posted by purphektdeletethis