⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Bridgeport draw bars looking for a home

Sorting out some stuff just now I realised I still have two unused replacement Bridgeport (type M) draw bars. I collect...
0 comments posted 18yrs
posted by cliffrayS
0 comments posted 18yrs posted by cliffrayS

Vulcan Beam Engine drawings.

I have acquired a set of castings for the Vulcan Beam Engine featured in the Model Engineer construction series started...
1 comments posted 18yrs
posted by binswood
1 comments posted 18yrs posted by binswood

Thumping cast-iron

I need to mark some hole positions out on a cast-iron lathe backplate - is it OK to use a transfer punch and give it a...
6 comments posted 18yrs
posted by anotherid.3des0n
6 comments posted 18yrs posted by anotherid.3des0n

Free stuff

Hi folks, I have the following stuff available free: * Calor propane blowlamp, with a spare nozzle. Looks a bit beat, b...
3 comments posted 18yrs
posted by cdt22NOSPAM
3 comments posted 18yrs posted by cdt22NOSPAM

coffee cup stirling

Short video of Jan Ridders' Coffee Cup Stirling engine which is the free plan with the Vol.201.#4329, July 4-17 issue o...
1 comments posted 18yrs
posted by mcgray
1 comments posted 18yrs posted by mcgray

Super Simon

Would SKS be able to scan the articles on the Super Simon engine in Volume 171 #3948, #3950, and a Postbag mention in #...
0 comments posted 18yrs
posted by mcgray
0 comments posted 18yrs posted by mcgray

Sticking brass to mild steel

What's the best glue for sticking brass to mild steel? Super-glue? Araldite? Brendan
17 comments posted 18yrs
posted by anotherid.3dbm4o
17 comments posted 18yrs posted by anotherid.3dbm4o

Aluminium round or tube-3/16

Morning All, I have been trying to source aluminium round and tube in 3/16 dia but most of the model metal suppliers ar...
7 comments posted 18yrs
posted by bartlett.darius
7 comments posted 18yrs posted by bartlett.darius

Thrust washer material?

I'm needing to make a new thrust washer for the rotor drive sprocket on an old Howard 300 rotovator, but I'm not sure w...
9 comments posted 18yrs
posted by mtbhypenrules
9 comments posted 18yrs posted by mtbhypenrules

Wanted: Man and Women to work from home.

Wanted: Man and Women to work from home. Nationwide search! Wanted: Man and Women to work from home. Do you have some f...
0 comments posted 18yrs
posted by kabari9433
0 comments posted 18yrs posted by kabari9433

Taper shank milling cutters

I was recently given some as-new taper shank milling cutters (ex MoD I believe), and I am at a loss to know how to use...
0 comments posted 18yrs
posted by mike.crossfield
0 comments posted 18yrs posted by mike.crossfield

Taper shank milling cutters

I was recently given some as-new taper shank milling cutters (ex MoD I believe), and I am at a loss to know how to use...
13 comments posted 18yrs
posted by mike.crossfield
13 comments posted 18yrs posted by mike.crossfield

4 pole 160 / 200a isolator

Has anyone a 4 pole (ie 3 phase with switched neutral) isolator / switch disconnector / switch fuse with a rating of 16...
8 comments posted 18yrs
posted by andrew
8 comments posted 18yrs posted by andrew