⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

machinery moving ?

has anyone any idea how much it would cost me to move a 1 ton machin from birmingham to york ? or any suggestions as to...
0 comments posted 20yrs
posted by willowkevin.2d5vob
0 comments posted 20yrs posted by willowkevin.2d5vob

stone colours?

I recently bought a set of tools for a Dremel. There are four sets of mounted stones, white, pink, greeny-blue and grey...
6 comments posted 20yrs
posted by zenadsl6186
6 comments posted 20yrs posted by zenadsl6186

What lathe/mill - advice please.

Hello all, Just finished converting the garage and now ready to purchase lathe and milling machnine. Floor area is 17x1...
36 comments posted 20yrs
posted by halgate(nospam)
36 comments posted 20yrs posted by halgate(nospam)

HS 1020

Good afternoon I was wondering if you could help me with some information. My father in law has just come into possessi...
3 comments posted 20yrs
posted by andypeg
3 comments posted 20yrs posted by andypeg

Beer Vouchers ready & waiting

For my next roundtoit project, I'm looking for a 3HP 3 phase motor. Specification Flange mount size 90 frame or perhaps...
8 comments posted 20yrs
posted by bob.minchin
8 comments posted 20yrs posted by bob.minchin

Milling Spindle Motor

Hi All I am planning to make a milling spindle for my chipmaster lathe. I cannot decide which type of motor would be be...
18 comments posted 20yrs
posted by alan
18 comments posted 20yrs posted by alan

Not flat, but flat enough.

Today I wrestled the 2'x3' surface table that I got via ebay into the workshop. I'd actually got it in May 2004 from th...
0 comments posted 20yrs
posted by randm
0 comments posted 20yrs posted by randm

Band saw

The metal bandsaw turned up today from Warco. I assembled the flat pack stand and mounted the main saw to it, fitted gu...
8 comments posted 20yrs
posted by adrian
8 comments posted 20yrs posted by adrian

Motor connections on Warco WMT300 lathe

Can anyone please confirm the motor connections on a Warco WMT300 lathe motor. The motor has four terminals labelled D1...
0 comments posted 20yrs
posted by gary
0 comments posted 20yrs posted by gary

Shell Ensis oil ('non-drying' rust prevention)

In George Thomas's book 'The Model Engineer's Workshop Manual' he i very clear that Ensis oil 152 or 158 (SAE20) from S...
11 comments posted 20yrs
posted by Myford.Matt.2d00kb
11 comments posted 20yrs posted by Myford.Matt.2d00kb

Removing a toolpost

My Holbrook C10 has a 4-way toolpost that the manual calls a "turret" but I want to replace it with the Multifix that I...
3 comments posted 20yrs
posted by nomail
3 comments posted 20yrs posted by nomail

16DP lathe gears needed

Anyone know where I can get 16DP gears in 20 and 30 teeth sizes (14.5 degree pitch angle) - i.e. standard screwcutting...
10 comments posted 20yrs
posted by oldnoccer
10 comments posted 20yrs posted by oldnoccer

Bridget locomotive

I'm hoping someone on here can help. Whilst browsing the Reeves stand at the recent Bristol Show, I noticed the gunmeta...
1 comments posted 20yrs
posted by alastair.j.m.clarke
1 comments posted 20yrs posted by alastair.j.m.clarke

LIDL - this week

So, I got carried away at LIDL when I went in to pick up a 150mm digital vernier for £9.99, and also came back with :-...
23 comments posted 20yrs
posted by malcolm_stewart
23 comments posted 20yrs posted by malcolm_stewart