⚙ Model Engineering in the UK

Stationary engine model engineering publication

Does anyone have a copy of this book. http://www.stationary-engine-magazine.co.uk/cgi-bin/purchase.cgi?cat=Stationary_E...

0 comments posted 21yrs

posted by davecroft

0 comments posted 21yrs posted by davecroft

Bureaucracy Looming?

I was talking to a well-known engine man and friend this morning, who passed this little gem to me by email. As far as...

26 comments posted 21yrs

posted by prepair

26 comments posted 21yrs posted by prepair

Happy Ending

As some of you will remember my workshop was broken into a while ago and several items were stolen. Not surprisingly th...

1 comments posted 21yrs

posted by kevin.newsgroups

1 comments posted 21yrs posted by kevin.newsgroups

TAP & Die

I would like to try and make some turnbuckles for my RC car and have been looking at TAP and DIE sets. Problem I have i...

3 comments posted 21yrs

posted by gavin.metcalfe

3 comments posted 21yrs posted by gavin.metcalfe

OT Scanning b & w negatives..

Never been a photography buff, I need thoughts.. I've got a few old negatives that I'd like to print out.. I don't seem...

7 comments posted 21yrs

posted by tmartin

7 comments posted 21yrs posted by tmartin

Looking for 10-24 UNC screws

I need a couple of 10-24 UNC x 3/8" screws for a repair job I'm doing but I can't find a source apart from buying a hug...

3 comments posted 21yrs

posted by aholeintheground

3 comments posted 21yrs posted by aholeintheground

Manchester - London/South East anyone

I've just bought a small Kennedy hacksaw via a well known engineering buy and sell website. The problem is that it's in...

11 comments posted 21yrs

posted by wells_hall

11 comments posted 21yrs posted by wells_hall

Quiet isn't it?

..or is it that everyone has forgotten that you know have to pay to use the Berlin newsfeed? Regards Charles http://www....

36 comments posted 21yrs

posted by wells_hall

36 comments posted 21yrs posted by wells_hall

40 tpi puzzle

I bought what I thought were taper and bottom 3/16 ME taps and die recently. Got them out today and the die has BSW 3/1...

2 comments posted 21yrs

posted by cbuffer

2 comments posted 21yrs posted by cbuffer

Alan Bloom (Bressingham)

Alan Broom Has died of Bressingham fame aged 98. CJ

0 comments posted 21yrs

posted by colin.jacobs

0 comments posted 21yrs posted by colin.jacobs

Boxford Paint - Help

I've recently acquired a 1978 Boxford BUD Lathe in good condition, although the paintwork is a bit shabby; its the two...

1 comments posted 21yrs

posted by pete

1 comments posted 21yrs posted by pete

Splined Couplings

I'm still pursuing this daft idea of the electro-hydraulic tram! I have now acquired a more powerful gear pump that giv...

2 comments posted 21yrs

posted by peter

2 comments posted 21yrs posted by peter

I have written a new program

Hello, I have written a new program to make rulers. ( straight and round ) It generates G-Code. You can download it for...

0 comments posted 21yrs

posted by majosoft

0 comments posted 21yrs posted by majosoft

Boxford Parts

The top slide on my Southbend had rather a lot of play in it, and I managed to buy a secondhand Boxford top slide to fi...

0 comments posted 21yrs

posted by kevin.newsgroups

0 comments posted 21yrs posted by kevin.newsgroups

Mixer tap thread/adapters

During the current kitchen refit, we bought a new sink on ebay and picked it up from Milton Keynes this morning. It did...

5 comments posted 21yrs

posted by diesel

5 comments posted 21yrs posted by diesel