⚡ Welding Forums

small stuff

I want to weld some thin Inconel tube and sheet, about 0.02" (0.5mm) thick. I'd also like to be able to do welds in ver...

5 comments posted 20yrs

posted by zenadsl6186

5 comments posted 20yrs posted by zenadsl6186

newbie with a bit of a story

in my previous job, I learned how to weld with a gas MIG welder, and did quite a few projects with them (some being loa...

9 comments posted 20yrs

posted by Tater1337

9 comments posted 20yrs posted by Tater1337

Oxygen regulator for argon

Is it ok to use an oxygen regulator for argon. I know the part that attaches to the bottle has to be changed. stan

2 comments posted 20yrs

posted by sbaer

2 comments posted 20yrs posted by sbaer

STJ Reference

Hi, i'm bacheloring and i need some good references and infos about Structural Transition Joint and in particular about...

0 comments posted 20yrs

posted by emailnonvalida

0 comments posted 20yrs posted by emailnonvalida

OT tube bending

I am getting ready to form an exhaust system for a Landrover project of mine, I have taught myself TIG to a standard th...

14 comments posted 20yrs

posted by steve

14 comments posted 20yrs posted by steve

OT: MIKE GRAHAM

I have a message for Mike Graham. If anyone knows his email address or his whereabouts the follwing person from Birfiel...

3 comments posted 20yrs

posted by heartofvenus

3 comments posted 20yrs posted by heartofvenus

Anyone from the UK tried the Ready Welder??

I am thinking about getting a Ready Welder (a battery powered 24 volt spool gun welder) Has anyone from the UK got any...

1 comments posted 20yrs

posted by doorbell

1 comments posted 20yrs posted by doorbell

LiftArc and arc maintenance when in squarewave mode

Folx, was wondering what pros think of lift-arc feature, as opposed to HF - is it as good/convenient ? Also, assuming on...

1 comments posted 20yrs

posted by rashid.karimov

1 comments posted 20yrs posted by rashid.karimov

cutting torch

Can anyone tell me the proper distance for the tip to the material? I've read all kinds of articles on using the cutting...

4 comments posted 20yrs

posted by tcary

4 comments posted 20yrs posted by tcary

TIG welding plasma cut edges

Hi All, I am considering buying a plasma cutter probably the Powermax 1000 and have been trying without much sucess to...

10 comments posted 20yrs

posted by daved

10 comments posted 20yrs posted by daved

New Uk Welders

I found a new Uk supplier of inverter welders may be worth checking out. www.betacentury.co.uk

2 comments posted 20yrs

posted by dave.smithlds

2 comments posted 20yrs posted by dave.smithlds

Which Brazing Filler

need to use my TIG to Braze fill 304 ss to mild steel. my local shop told me that the silver rods would work (they say...

5 comments posted 20yrs

posted by kryptoknight

5 comments posted 20yrs posted by kryptoknight

Harbor Freight

Is Harbor Freight's inverter worth hauling home for $200?

17 comments posted 20yrs

posted by dancing

17 comments posted 20yrs posted by dancing

What kind of steel is this???

I was at the scrapyard today and picked up some cutters. Here is a photo: http://www.drizzle.com/~dantzler/images/shop/...

0 comments posted 20yrs

posted by potato

0 comments posted 20yrs posted by potato

Hobart CyberTig 200 DCS question

I have a Hobart CyberTig 200 DC-S welder. It is a 3 phase 200 A rated SCR fired, transformer based TIG welder. I have a...

6 comments posted 20yrs

posted by ignoramus19116

6 comments posted 20yrs posted by ignoramus19116