⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

to point or not

I posted this over on the Miller site (Ask Andy) but didnt get an answer so I thought Id put the question to the news g...
12 comments posted 22yrs
posted by goddard
12 comments posted 22yrs posted by goddard

small inverter welder

Hi, Can anyone give me a short and simple run down on the small inveter stick welder that are not set up for tig welding...
2 comments posted 22yrs
posted by jeisen
2 comments posted 22yrs posted by jeisen

best way to learn mig welding?

Hi All, I'm working in a medium sized engineering firm (around 40 full time staff) and produce mainly agricultural prod...
0 comments posted 22yrs
posted by askshaun
0 comments posted 22yrs posted by askshaun

Square tubing bender suggestions

I need a bender. Mostly, I will be bending solid square bar, rod, and flat bar. Occasionally, I might want to bend the...
8 comments posted 22yrs
posted by deserttraveler
8 comments posted 22yrs posted by deserttraveler

Miller 300AC/DC Shopmaster..........

What are the deficiencies of this machine in the MIG/TIG/stick configuration ? I'm considering a used one less than 10...
4 comments posted 22yrs
posted by ccthomas
4 comments posted 22yrs posted by ccthomas

Miller Balancing Resistor

Hello I have an older Miller 330ABP TIG welder and have thought of bypassing the Balance Resistor , the resistor is mad...
1 comments posted 22yrs
posted by PDL
1 comments posted 22yrs posted by PDL

Bring back the HP 15C Scientific calculator

I have been working on an effort to get HP to start making the 15C, or a similar model again. To this end I have set up...
6 comments posted 22yrs
posted by 1qazse4XYZ
6 comments posted 22yrs posted by 1qazse4XYZ

Circuit board for my Miller

Does anyone know where I can get a circuit board at a decent price for my Millermatic 185? It is the one for the wire f...
13 comments posted 22yrs
posted by adamsfam
13 comments posted 22yrs posted by adamsfam

Which Plasma cutter to buy?

I'm about to pick up one of these. I need something that is portable, runs off 230vac 50Hz, and will routinely cut up t...
1 comments posted 22yrs
posted by pbarryplennoxp
1 comments posted 22yrs posted by pbarryplennoxp

Burns

My son is a welder and is always getting burned... mostly on his upper arms. Is there anything I can buy for him that w...
4 comments posted 22yrs
posted by willlocksley
4 comments posted 22yrs posted by willlocksley

Need help with broken bandsaw base.

Sometimes I amaze myself at my stupidity and lack of forethought. I've managed to break the base casting of my Jet 4x6"...
8 comments posted 22yrs
posted by lane_nospam
8 comments posted 22yrs posted by lane_nospam

Spot-welding .040" 308L CRES SS rod

crossposted to sci.engr.joining.welding and sci.electronics.design please manage followups intelligently, thanks. I've...
4 comments posted 22yrs
posted by null
4 comments posted 22yrs posted by null

Question about Mig Welder

Been thinking of getting a Mig welder for my side business. I've seen several good looking 110volt units from Lincoln,...
7 comments posted 22yrs
posted by twofas4luv2000
7 comments posted 22yrs posted by twofas4luv2000

TIG vs. Stick - Maximum material thickness

Hi all, I'm in the process of getting a used TIG welder running. It (a Powcon 300ST) will also do stick welding, and I'...
13 comments posted 22yrs
posted by pgrey
13 comments posted 22yrs posted by pgrey