⚡ Welding Forums

Titanium Mig wire

I am looking for a UK or europe supplier of Titanium MIG welding wire Preferably with online ordering Anyone got any ide...

0 comments posted 22yrs

posted by dark-angel(nospam-remove)

0 comments posted 22yrs posted by dark-angel(nospam-remove)

galvanized metal

I was planning to use some galvanized metal (actually roofing flashing) to repair my grill... but a friend mentioned th...

11 comments posted 22yrs

posted by tapenick

11 comments posted 22yrs posted by tapenick

non-gas TIG?

Has anyone ever heard of flux-cored or flux coated TIG rod? Is there any reason why this wouldn't work? thanks

6 comments posted 22yrs

posted by carter

6 comments posted 22yrs posted by carter

How much workspace ?? Sparks - Danger Zone

Well I've got all my advice ... ready for MIG ... 50 amps in .. metal table in place ... and ready to go w/ either Mill...

8 comments posted 22yrs

posted by jeff-klein

8 comments posted 22yrs posted by jeff-klein

MIG Welding vertical surfaces

Hi, On the weekend I was welding 3mm angle iron together.. I got some great looking welds when I was welding on a horiz...

4 comments posted 22yrs

posted by cedric

4 comments posted 22yrs posted by cedric

Step Up transformers.

Has anyone tried slaping a big step up transformer (110v source to 220v outlet) to a 220v welder. It seems with a large...

2 comments posted 22yrs

posted by jtrain

2 comments posted 22yrs posted by jtrain

Titanium Wire

I am looking for a UK or europe supplier of Titanium MIG welding wire Preferably with online ordering Anyone got any ide...

0 comments posted 22yrs

posted by dark-angel(nospam-remove)

0 comments posted 22yrs posted by dark-angel(nospam-remove)

Zirconiated tungsten...Fantastic

I just tried out some new zirconiated tungstens for tig on aluminum. I cannot believe how much better than pure tungste...

11 comments posted 22yrs

posted by r9565

11 comments posted 22yrs posted by r9565

web site

Look at web site www.steel-link.com to see some good things

0 comments posted 22yrs

posted by wilsonwelding

0 comments posted 22yrs posted by wilsonwelding

SMAW coffee cans?

I want to prototype a better muffler for a small engine. I don't want to put much money into it, nor can it be too heav...

15 comments posted 22yrs

posted by LawrenceSMITH

15 comments posted 22yrs posted by LawrenceSMITH

Silly Q re electrocution

Guess a Q re being electrocuted is not really silly, at least not as silly as NOT asking it! Anyhow, I have a Steel Wor...

40 comments posted 22yrs

posted by Fredbear2412(via)yahoo.com.au

40 comments posted 22yrs posted by Fredbear2412(via)yahoo.com.au

about newbie welders....

I dont know about the rest of you guys but being an experienced welder and seeing these posts about inexperienced welde...

49 comments posted 22yrs

posted by dschledewi

49 comments posted 22yrs posted by dschledewi

Common Ground (for welding)

90% of my welding work takes place on a 4'x8' (probably 500#) table. a tig, mig and two stick machines are up against a...

9 comments posted 22yrs

posted by antoniogatta

9 comments posted 22yrs posted by antoniogatta

alumanized steel

What is the best wire/gas setup to weld 22ga. alumanized commercial exhaust duct.Also w.s/ volt/amp/slope settings plea...

1 comments posted 22yrs

posted by WELDZALL

1 comments posted 22yrs posted by WELDZALL

aluminum solder from Bernzomatic

I picked some rods up(al3 4043) but there are no instructions and the Bernzomatic web site is useless. Do you need a fl...

1 comments posted 22yrs

posted by lavinsky

1 comments posted 22yrs posted by lavinsky