⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

FS NICE Airco Mig

PhaseArc 350, with near new Tweeco gun. 240-460 3ph on cart with Smith regulator. Excellent shape, have photos. This is...
0 comments posted 17yrs
posted by gunner
0 comments posted 17yrs posted by gunner

tig torch/tig welder

I'm planing to by a tig welder soon, and have been looking at the Miller dynasty 200dx. It doesn't come with any cables...
7 comments posted 17yrs
posted by notme
7 comments posted 17yrs posted by notme

Funny Welding Cartoon

Heheh, found this on Youtube http://www.youtube.com/watch?v=6oSdWqerwxM "We weld the children... no mommy no!" lololol...
3 comments posted 17yrs
posted by absolutetwitter_at_gmail_dot_c
3 comments posted 17yrs posted by absolutetwitter_at_gmail_dot_c

high temp thread lubrication?

I have recently acquired a large ceramic outdoor cooker. The top damper threads up and down to open/close. Temps inside...
18 comments posted 17yrs
posted by grantNOSPAM
18 comments posted 17yrs posted by grantNOSPAM

Built a circle cutter

I have been toying for a while with building a circle cutter to mount on the same burning table I have my old Airco Cam...
3 comments posted 17yrs
posted by ernie
3 comments posted 17yrs posted by ernie

Tubing Repair

I have a nice big gate, about 18 feet long, that I'm fixing. It swings up and down from a single pivot, and it was orig...
10 comments posted 17yrs
posted by tim
10 comments posted 17yrs posted by tim

Small hoses?

Hi all, I inherited a little Purox / Linde / Union Carbide W200 OA set recently. After a little cleanup, it works reall...
15 comments posted 17yrs
posted by Winston
15 comments posted 17yrs posted by Winston

O/A Cutting - Results

Ok, guys thanks. I have no idea what tip I have. Its a generic HF. My O2 gage is a Smith and my Acet gage is a Gentec t...
13 comments posted 17yrs
posted by nospam
13 comments posted 17yrs posted by nospam

FS -- Lincoln Ranger welder, 120 hours, Chicagoland

120 hours on a engine driven welder like this, would correspond to 19 year age in girls, more or less. Runs great and co...
5 comments posted 17yrs
posted by ignoramus27816
5 comments posted 17yrs posted by ignoramus27816

Welding jewelry bracelet clasp made of "925 silver"

At a Marshall's parking lot, I found a silver bracelet made of 925 silver. The only problem with it is that on the clas...
10 comments posted 17yrs
posted by ignoramus18810
10 comments posted 17yrs posted by ignoramus18810

NDE Residual Stress

NDE RESIDUAL STRESS - NEW METHOD Introduction Internal stresses are to be considered as the following: 1) Operational s...
0 comments posted 17yrs
posted by rst200_at_fastwebmail_dot_it
0 comments posted 17yrs posted by rst200_at_fastwebmail_dot_it

Jailhouse door - Bit questions

I am building a jail house door. 3/4" bar for the verticles and 5/4"x1/4" flat stock for the horizontals. I'm going to...
16 comments posted 17yrs
posted by powersupplyguy
16 comments posted 17yrs posted by powersupplyguy

can't get penetration on broken bolt

I haven't posted to this group in a couple years, but now I'm stuck. I'm trying to remove a broken exhaust bolt from a...
23 comments posted 17yrs
posted by dlwilson
23 comments posted 17yrs posted by dlwilson

E 7016 electrode

I have some E 7016 electrodes and need to refresh why I got them. Have looked on the internet and not found anything th...
19 comments posted 17yrs
posted by dcaster
19 comments posted 17yrs posted by dcaster