⋐⋒⋐ Computer Numeric Control

  1. Home
  2. ⋐⋒⋐ Computer Numeric Control
2667 Threads Posts
to

Seeking a Special Chop or Cut-Off Saw

The other day, some cable TV show about trucks (I think) had this new low RPM, no dust cut-off saw that also allowed mi...
10 comments posted 18yrs
posted by bob
10 comments posted 18yrs posted by bob

OT-The Jeffersons

Moving on up seems the Jeffersons (close knit bunch) will all get to spend some time in the joint together. Congressman...
1 comments posted 18yrs
posted by debco99
1 comments posted 18yrs posted by debco99

Which Way Would You Rather Modify This Part?

For months ignorant CADCAM idiot Tom Brewer insisted that a roll back bar was just fine and all I needed was more train...
21 comments posted 18yrs
posted by jon_banquer
21 comments posted 18yrs posted by jon_banquer

New Page Added To The Jon Banquer Blog

The new page is: Why You Should Know And Care What Techsoft 3D HOOPS Is The Jon Banquer blog is the only blog dedicated...
11 comments posted 18yrs
posted by jon_banquer
11 comments posted 18yrs posted by jon_banquer

Pipe Taps

What is the difference, if any, between NPT threads and NPTF threads? Thanx, -plh
1 comments posted 18yrs
posted by plh_member
1 comments posted 18yrs posted by plh_member

Tooling University and the IMTS show

Several people have asked about CNC and shop management training in this NG. Tooling University is an on-line source. c...
0 comments posted 18yrs
posted by gmcduffee
0 comments posted 18yrs posted by gmcduffee

Demagnetizing Digital Calipers?

To All: What are your thoughts on putting digital calipers on an electric magnetic surface grinder chuck (that has a dem...
10 comments posted 18yrs
posted by bottlbob
10 comments posted 18yrs posted by bottlbob

power supply electronics query

Need some help identifying several power supply capacitors that are blown, inside a 200V DC power supply. The caps are...
6 comments posted 18yrs
posted by a_design
6 comments posted 18yrs posted by a_design

Should The Jon Banquer Blog Add Machining Tips?

I have several three ring binders filled with machining notes I've made and collected over the years. Should I post the...
39 comments posted 18yrs
posted by jon_banquer
39 comments posted 18yrs posted by jon_banquer

Ground Loop Problem on CNC

I have discovered a ground loop potential of 3.0VAC between a CNC lathe and common ground of seperate 120v plug. The ma...
17 comments posted 18yrs
posted by sammer003
17 comments posted 18yrs posted by sammer003

PING: Dan Murphy

Dan, Have some questions regarding Tsugami lathes. Looks like your email is intended to thwart spammers. Can you shoot m...
1 comments posted 18yrs
posted by janders1957
1 comments posted 18yrs posted by janders1957

RIP SurfCAM?

What's the deal with Surfcam? A little birdie told me they were in serious financial trouble and may actually fold. The...
25 comments posted 18yrs
posted by nobody
25 comments posted 18yrs posted by nobody

Free tool path software

Are there any free tool path verification software out there? Buddy is wanting to be able to check tool paths on okuma...
2 comments posted 18yrs
posted by gunner
2 comments posted 18yrs posted by gunner

Need desoldering advice

I was working on a lathe with a Fanuc 0-TC control today that could not download programs and I suspect the 751488 line...
28 comments posted 18yrs
posted by clutch
28 comments posted 18yrs posted by clutch