1. Home
  2. Engineering Science (Polish)
  3. róznica

róznica

jaka jest róznica w gwintach calowych G1 1/8" a R1 1/8" według mnie
jest ten sam gwint al;e jeszcze nie jestem pewien mimo przewertowania
wielu poradników. dzięki za pomoc.
Reply to
bruno
Loading thread data ...
bruno napisał(a):
Gwint R1" to gwint rurowy stożkowy; szczelność uzyskuje się na samym gwincie. Gwint G1" to gwint rurowy walcowy; szczelność uzyskuje się przez zastosowanie uszczelki.
Reply to
Goska

Site Timeline

Related

  • porosity in 1/8 7018

  • How do I eliminate the porosity (or what causes it) in a pipe welded with 1/8...

  • spot welding 1/8 steel?

  • I don't have much experience spot welding. I am looking at an assembly that...

  • welding table from 1/8" plate?

  • I would like to have a little welding table for welding smallthings. I have a...

  • dro for gorton 8 1/2d mill

  • I have a 1956 model Gorton 8 1/2d vertical milling machine with a compoundhead ,...

  • Bending 1" X 1/8" aluminum bar

  • I have to put 35=B0 bends in 1" X 1/8" aluminum. I tried a vice andhammering the...

  • Motori 1:8...

  • Volevo chiedervi: i motori da 3,5cc delle 1:8 hanno sempre bisogno...

  • Jaguar 1:8

  • Ile kosztowaloby zlozenie przez kogos z was modelu Jaguara E-type w skali 1:8...

  • 1/8" BSPT

  • Is there any way to cut a 1/8 BSPT thread apart from a taper turningattachment...

  • 1:8 elettrico

  • A qualcuno interessa? sto sviluppando un 1:8 elettrico concaratteristiche da...

  • Misure 1:8

  • Quali sono le misure standard (se ci sono) per un'auto radiocomandata in...

  • URGENT VENDS MAQUETTE FERRARI PORCHER 1/8

  • URGENT VENDS FERRARI PORCHER1/8VENDS 1 FERRARI TESTAROSSA CABRIOLET ...

  • Glattbahner 1:8

  • Hall d.r.m.m,vor einiger Zeit (~10 Jahre) bin ich 1:8 Verbrenner gefahren,...

  • Qty 1 1/8" BB :)

  • Fell out and, naturally, disappeared, of quick change hex chuck in me Hitachi...

  • 40G 1/8" thread ?

  • Hi FolksI need to cut a filter thread into a 1.25" telescope eyepiece barrelwith...

  • 1/8 scale corvettes

  • Got a beater 1/8 scale Sting Ray on Ebay, and a beater 1/8 scale C5 (?)Vette....

  • Kit auto 1:8

  • Salve ragazzi ma si trovano ancora in giro modelli di auto da costruire 1:8? Mi...

  • Albrecht 1/8" to 5/8" Chuck

  • I Picked up a used Albrecht 1/8" to 5/8" chuck. Seems to operate verysmoothly,...

  • AVVIAMENTO MODELLO 1:8

  • Ragazzi ho un altro quesito da porvi.Vorrei costruirmi una base per messa in...

  • Minimum radius for 2-8-8-2

  • OK - I've put my Big Boy up for sale on eBay, but I may hold onto my...

  • Róznica między forged a wrought

  • Witam, Dostałem od klienta specyfikację na kształtki i część z nich jest...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.