Anyone need Drill chucks?


Ive been cleaning out my various bins, drawers and cabinets, getting
stuff togther for the big Clausing 15x40 lathe and whatnot,,,and keep
finding drill chucks. Ive got chucks with #1 MT spuds all the way up to
#4 Mt with 3/4" jacobs drill chucks on them. All are in excellent
condition, some appear nearly new..a couple ARE new.
Anyone need anything? I figure I can sell some of them and buy that
damned expensive belt that I need for the Clausing lathe and still be
able to buy dog and cat food. They would probably bite me if I let
em go hungry and bought that $100 belt.
Ive got chucks with R8 holders, chucks with threaded ass ends (looks
like 1/2-20..Ill check on them.
Frankly..Ive got at least 20 good drill chucks and I damned sure dont
need that many.
I could use both NMTB 30 and NMTB 40 tool holders with either drill
chucks or tapers for installing drill chucks, if anyone has any kicking
around as spares.
Anyone?
Gunner
The current Democratic party has lost its ideological basis for
existence.
- It is NOT fiscally responsible.
- It is NOT ethically honorable.
- It has started wars based on lies.
- It does not support the well-being of americans - only billionaires.
- It has suppresed constitutional guaranteed liberties.
- It has foisted a liar as president upon America.
- It has violated US national sovereignty in trade treaties.
- It has refused to enforce the national borders.
...It no longer has valid reasons to exist.
Lorad474
Reply to
Gunner Asch
Loading thread data ...
I could use a 16N chuck with a #2 MT, I could trade you one that holds a drill crooked. I might be able to use just a jaw repair kit too if anyone has one of those.
Thank You, Randy
Remove 333 from email address to reply.
Reply to
Randy
I would like an R8 16N chuck.
Myself, I have a bunch of MT2 Jacobs superchucks for sale.
i
Reply to
Ignoramus6241
Would be interested in Kennemetal 3/8", 5/8" or 3/4" DA style with J33 or MT2 mounts.
Reply to
Joe AutoDrill
Ill do an inventory this afternoon and post it. Whats a good one worth to you?
I dont have any repair kits unfortunately. Shrug..when I wound up with all these chucks...I didnt figure I needed any.
Reply to
Gunner Asch
Thats 1/8-58" Ive got at least 4 of them..I think Ive got a couple with R8.
Whats a very good condiiton one worth to you? Oh...I may have one or two chuck keys available..but not many for any of the chucks.
Make me an offer.
Gunner
Reply to
Gunner Asch
I dont think there are any Kennemetals out there. The vast majority are Jacobs, followed by Albrecht and Rohms
Gunner
Reply to
Gunner Asch
I have a belt supplier that is very reasonable, send me the specs. and I might trade you that belt for what's behind door number one.
Reply to
Buerste
2528v370....variable speed belt.
Thanks for checking. Best Ive found so far is $79. Clausing wants...$108 plus shipping
Its claimed thats not a Perfect fit..shrug..but it works.
Gunner
Reply to
Gunner Asch
Gunner, my FIL needs a Morse taper chuck for his drill press. I'll get the size and get back to you.
Steve
Reply to
Steve B
I am lookin for a good keyless chuck, but not bad enought to spend the bucks on a new one! I have 1/2 and 5/8" key chucks already. Maybe a MT#2-#3 reducer, and a few odd MT drill bits, 1/2", 5/8" 3/4", and on up to 1", and/or 1/32 over in those sizes. Greg O
Reply to
Greg O
I have a MT3 Jacobs 18N Superchuck, up to 3/4", $75 plus shipping. I have two and need only one. It is not keyless, though.
shars.com has a keyless chuck very inexpensively.
i
Reply to
Ignoramus27518
Cool. Just tell me what you need.
Gunner
Reply to
Gunner Asch
Ive got 3..no..4 german keyless chucks, 2 Albrects, 1 Rohm and another which I cant remember. Ill post pictures. Biggest Albrect is 5/8..the rest are 1/2".
Ive got about 50 #2 MT drills I found, all laid out neatly in 2 cookie trays...they run about 3/8-1/2"..maybe a bit bigger. Covered with dust..its on my list of things to go through.
I dont think Ive got a MT2-MT3, but did find an MT2-MT4, which Ill probably hand on to.
How much are you willing to pay for a good..good keyless? Gunner
Reply to
Gunner Asch
"Ignoramus27518" wrote in message >
Not intterested, I have keyed chucks. Greg O
Reply to
Greg O
1/32" - 1/2" with MT 2 or 3 taper, $75 maybe $100+ if it is a darned nice one! I see them on Ebay around that price. I am not interested in MT drills under 1/2". Looking for drills over 1/2" in MT. Greg O
Reply to
Greg O
Got a near new 5/8 Albrect, but doesnt have a taper. Empty socket.
Got a very very nice Seiko, MT2, 1/2" Got a decent Rohm, 1/2" and a pretty fair Grand (german) 1/2"..I think..think both of these are straight 1/2" studs for mills..maybe 5/8ths. Ive been doing other stuff today after the rain.
Ill post some photos later tonight or tommorow morning.
MT2? Or MT1? I think I can get near 3/4" in MT2, but these are longer drills. Probably 8" beyond taper.
Gunner
Reply to
Gunner Asch

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.