⏣ General Metalworking

30777 Threads Posts
to

Lubricant

The manual that came with the milling machine mentions that the unit is covered in heavy grease and this must be remove...
20 comments posted 20yrs
posted by webreply
20 comments posted 20yrs posted by webreply

Dropbox post Cheep MIG upgrade

Hey All! I did a simple upgrade to my cheapo MIG (to keep it from overheating) and posted it to the dropbox. Look for mi...
2 comments posted 20yrs
posted by carl.byrns
2 comments posted 20yrs posted by carl.byrns

Are there any adjustable reamers under 1/4" ?

I need to ream holes that will range between 3/16" and 1/4". The actual size can vary due to the fact that what goes in...
4 comments posted 20yrs
posted by myName
4 comments posted 20yrs posted by myName

Lost wax casting help sought

Greetings to all the Casters out there, It seems that all the ingredients required, except for de-bubblizer, are now as...
2 comments posted 20yrs
posted by etpm
2 comments posted 20yrs posted by etpm

OT- Painting inside a microwave

Got a bigger microwave for cheap (like free). HUGE inside, but paint is chipped, blistered inside. Anyone done, or know...
6 comments posted 20yrs
posted by res6nlr2
6 comments posted 20yrs posted by res6nlr2

OT: make CD boot disk

I bought a 160 gig hard disk at Best Buy ($36 after rebate). I'm putting a copy of all my software CDs on it. My Window...
6 comments posted 20yrs
posted by karltownsend.NOT
6 comments posted 20yrs posted by karltownsend.NOT

RPC questions

Im about ready to finish up my 10hp rotary converter (pony motor start) and need a source and some info, for balanceing...
13 comments posted 20yrs
posted by gunner
13 comments posted 20yrs posted by gunner

Gratuitous swarf photos

For those of you who like to watch, here is a three-page photo essay showing the construction (incomplete as yet) of a...
26 comments posted 20yrs
posted by contact.me
26 comments posted 20yrs posted by contact.me

10 HP idler motor starting: 120 amps!

Did a little experiment... I clamped a clamp on ammeter on the single phase supply wire for my 10 HP idler, and flipped...
7 comments posted 20yrs
posted by ignoramus4758
7 comments posted 20yrs posted by ignoramus4758

Twisting round stock for railings

I'm having trouble getting my head around this one. I'd like to create an effect like the one in the dropbox entitled "...
5 comments posted 20yrs
posted by cfam4
5 comments posted 20yrs posted by cfam4

V Belt or Roller Chain?

I plan on buying a "Voltage Master" 5 KW generator (3600 RPM) that I will power from my tractor front PTO. I would like...
18 comments posted 20yrs
posted by nospam
18 comments posted 20yrs posted by nospam

Cheap source for Casio G-shock watches?

My old daily friend..a Casio G-shock watch has finally bitten the dust after at least 10 yrs of daily abuse. Regular su...
39 comments posted 20yrs
posted by gunner
39 comments posted 20yrs posted by gunner

HOW WOULD YOU do it?

I have a stainless, small, pony keg that I want to cut in half lengthwise in order to make a barbeque to hang of the si...
17 comments posted 20yrs
posted by finalact
17 comments posted 20yrs posted by finalact

Can I do this with a nibbler?

I have never used a nibbler, or even seen one used, but I think it might be just the tool for this job. I am using some...
4 comments posted 20yrs
posted by garyh82012
4 comments posted 20yrs posted by garyh82012