⏣ General Metalworking

30777 Threads Posts
to

Dumb "current transformer" questions

Let's say that I have a cable and I want to measure the AC current going through it. Up to, say, 100 amps. I could use...
28 comments posted 20yrs
posted by ignoramus29580
28 comments posted 20yrs posted by ignoramus29580

Q: Tank Stand

Hi, I'm thinking of building a rack to hold 2 aquariums, using 1.5" 1/8" angle. Overall dimensions are 24w 60l 44h only...
10 comments posted 20yrs
posted by chrispol
10 comments posted 20yrs posted by chrispol

Colchester Student Mk 1 - some questions

Evening all (well it is here :-)). I've got a Mk1 Colchester Student lathe. Just been cutting thread on a bit of bar wi...
11 comments posted 20yrs
posted by austinNOSPAM
11 comments posted 20yrs posted by austinNOSPAM

A security bolt

Warning: metal content http://users.goldengate.net/~dforeman/security-bolt/
41 comments posted 20yrs
posted by dforeman
41 comments posted 20yrs posted by dforeman

davit advice needed

I am making a davit for a hoist. The davit (imagine a figure 4 with a long leg) will be about 14' high, with about a 3'...
3 comments posted 20yrs
posted by deserttraveler
3 comments posted 20yrs posted by deserttraveler

No good deed goes unpunished

I agreed last week to sell some things on ebay that my neighbor considered worthless. Now that they are sold, he is com...
11 comments posted 20yrs
posted by deserttraveler
11 comments posted 20yrs posted by deserttraveler

Can someone ID this lathe?

I just picked up an old and somewhat rusty lathe but can't figure out what it is, so I'll describe it as best I can. It...
17 comments posted 20yrs
posted by myName
17 comments posted 20yrs posted by myName

Machining Powdered Metal - ugh!

I just spent a couple of hours making an Ebay Browning two-groove sheave a bit smaller (4.75" pitch diameter to 4.25" P...
12 comments posted 20yrs
posted by viewptmd
12 comments posted 20yrs posted by viewptmd

small mill for home shop

I'm looking for a mill for my home shop. I've passed up a few great deals on Bridgeports (and a really nice hardinge la...
28 comments posted 20yrs
posted by berger
28 comments posted 20yrs posted by berger

OT: Suddenly no sounds at all in WMP 10

Sorry folks, it's me again with some Windows XP problems. And I am almost certain that this is a WMP specific problem....
20 comments posted 20yrs
posted by abrasha
20 comments posted 20yrs posted by abrasha

source for t-slot table?

hi! i am looking for a t-slot table/plate with roughly 36"x12"x2" dimensions. cast iron or steel. does anyone have any t...
6 comments posted 20yrs
posted by pixbroker
6 comments posted 20yrs posted by pixbroker

cleaning old grinding grit

I rebuilt an old surface grinder once, and now I'm rebuilding a 16" chop saw. Both emitted copious streams of grinding...
8 comments posted 20yrs
posted by grant
8 comments posted 20yrs posted by grant

[OT] Any good plastic working forum

I could not find a "plasticworking" forum anywhere. I am looking for a good group or forum dedicated to this subject: ma...
2 comments posted 20yrs
posted by nospam_nicver
2 comments posted 20yrs posted by nospam_nicver

Why can't people trade in a decent way?

Hi all, I apologise if this is a bit of a rant, but I seem to have had bad luck recently. First there was the mag drill...
27 comments posted 20yrs
posted by cdt22NOSPAM
27 comments posted 20yrs posted by cdt22NOSPAM

Service presentation

We are a Spanish company called TALLERES MEC=C1NICOS MAYPE located in Barcelona. We are specialized in the mechanizatio...
0 comments posted 20yrs
posted by maype
0 comments posted 20yrs posted by maype