⏣ General Metalworking

30777 Threads Posts
to

OT: 1ph motor hums

I recently bought a brand new Leeson 5 hp (20 Amp, 230 V) 1 ph "Compressor Duty" motor off Ebay. I made a quick test to...
9 comments posted 21yrs
posted by viewptmd
9 comments posted 21yrs posted by viewptmd

Source for Forms of Metal?

I have a group of friends who are looking for different forms of metal and I'm clueless where to acquire such for them....
3 comments posted 21yrs
posted by mattsonsolar
3 comments posted 21yrs posted by mattsonsolar

B&S Engine Q

In what newsgroup do the guys who are wizards with small Briggs & Stratton engines hang out? Technically there isn't an...
17 comments posted 21yrs
posted by GeoLane_NOSPAM_
17 comments posted 21yrs posted by GeoLane_NOSPAM_

Centering Scopes?

Over the years, a couple of people have mentioned being very fond of their centering scopes. I've been thinking of gett...
7 comments posted 21yrs
posted by gwhite
7 comments posted 21yrs posted by gwhite

Put some test to the rear lift I made for my bolens

I have a 1250 Bolens I fit an old hydro bumper jack to. I cut off the forks with the wheels and welded a frame to fit t...
4 comments posted 21yrs
posted by wayneREMOVETHIS
4 comments posted 21yrs posted by wayneREMOVETHIS

Bandsaw question

Hi all, Comming up before too long on the "next project to do" list is a bandsaw I have. It is a few year old (guessing...
7 comments posted 21yrs
posted by alanganes
7 comments posted 21yrs posted by alanganes

oil in propane regulator

I have a small propane heater, Mr Buddy, or something like that. I takes a 1lb propane bottle. I have made a long hose...
10 comments posted 21yrs
posted by alpinekid
10 comments posted 21yrs posted by alpinekid

Flat Belt step pulley

I'm looking for a source of flat belt step pulleys. I've searched around all the usual suspects (MSC, McMaster, Grainge...
4 comments posted 21yrs
posted by marc.britten
4 comments posted 21yrs posted by marc.britten

Bug mudda endmill

While sorting old metalworking books, I came across a photo in an old school textbook that showed a large press frame b...
6 comments posted 21yrs
posted by kmiller
6 comments posted 21yrs posted by kmiller

Outhouse Contest

I will be building an outhouse this spring at our mountain cabin. I want to make it the common two holer, one side with...
29 comments posted 21yrs
posted by deserttraveler
29 comments posted 21yrs posted by deserttraveler

Welding intercooler cores

I am trying to weld 6061 and 2024 alloys to my intercoolers, which are of unknown alloy. I have an OLD Miller Dialarc H...
4 comments posted 21yrs
posted by michalk
4 comments posted 21yrs posted by michalk

Grinder Spindle

Anyone know the specs for the spindle in the Delta Toolmaker/Surface grinder? I saw some wheel adapters that are for "s...
3 comments posted 21yrs
posted by jmartin957
3 comments posted 21yrs posted by jmartin957

best used machining center

I realized I should ask this in a more general sense. I am looking to buy a used machining center for about $10k - pref...
1 comments posted 21yrs
posted by WaltCarlM
1 comments posted 21yrs posted by WaltCarlM

Electropolishing

I've been experimenting with electropolishing stainless steel with limited success. I've tried various electrolytes - h...
10 comments posted 21yrs
posted by kg0mm
10 comments posted 21yrs posted by kg0mm

Dumoore flex shaft grinder question

I had forgotten Id scrounged up a Dumore flex shaft grinder some time back. The handpiece holds a 1/4" tool, which is a...
7 comments posted 21yrs
posted by gunnerNOSPAM
7 comments posted 21yrs posted by gunnerNOSPAM