⏣ General Metalworking

30778 Threads Posts
to

Myford Clutch

Does anyone have any information about the "Expanding Sleeve Clutch" as fitted to the early "Myford Super 7" The one's s...
1 comments posted 21yrs
posted by salamanda
1 comments posted 21yrs posted by salamanda

the 'puter scooter

There really is such a thing as a 15-minute project. More surprisingly, I was able to do one -- Jeff Wisnia take note!...
5 comments posted 21yrs
posted by dforeman
5 comments posted 21yrs posted by dforeman

Drill bit question

Is it OK to insert small drill bits deep into the chuck so that the flutes are being gripped by the chuck? Looking for...
8 comments posted 21yrs
posted by james
8 comments posted 21yrs posted by james

Signing off

It's finally happened, I'm going to sign off, probably permanently. Many reasons, the main one being that SBC raised my...
11 comments posted 21yrs
posted by Nobody
11 comments posted 21yrs posted by Nobody

Gingery Bandsaw book

One more question before bed :) Does anyone have a copy of Gingery's homemade bandsaw book they would be willing to sel...
3 comments posted 21yrs
posted by mano
3 comments posted 21yrs posted by mano

Air cooling blast device

Hi all, In the maintenance shop at the plant where I work, the machinist has a device mounted beside the milling machin...
5 comments posted 21yrs
posted by mano
5 comments posted 21yrs posted by mano

Logan 12" lathe being parted out

We will be parting out a Logan 12" lathe this week. The lathe is complete but has no accessories and I have already com...
3 comments posted 21yrs
posted by CATRUCKMAN
3 comments posted 21yrs posted by CATRUCKMAN

How to make very fine clock hands?

How did 18th century watch and clockmakers produce very fine steel hands?
9 comments posted 21yrs
posted by fdavidander
9 comments posted 21yrs posted by fdavidander

SAE Grade-8 bolt snapped @ 135ft/lbs

I'm dealing with a critical application. If these fasteners fail, the results could potentially be fatal. I need maximu...
37 comments posted 21yrs
posted by Cpeters1
37 comments posted 21yrs posted by Cpeters1

Twisting Lathe Bed Using Cabinet Bolts

I have a Sheldon 13x40 cabinet mounted lathe. It weighs in around 1200lbs. It has a large cast iron cabinet that the va...
1 comments posted 21yrs
posted by Sierevello
1 comments posted 21yrs posted by Sierevello

FS 4" angle grinder $10 new inc shipping

I accidentally bought more than I need, but then they were a bargain and I couldn't resist. New in box, plastic case, c...
4 comments posted 21yrs
posted by rex
4 comments posted 21yrs posted by rex

OT - Bad Intel 'Boxed CPU' heatsink

I'm in the process of building up 8 new Pentium 4 machines for work. I bought genuine Intel boxed CPU's with fan and he...
5 comments posted 21yrs
posted by jstewart
5 comments posted 21yrs posted by jstewart

Use for small angle grinders?

Well, somebody posted a neat site called last-minute auctions. Of course I had to try it, and wound up with 8 new 4.5"...
23 comments posted 21yrs
posted by rex
23 comments posted 21yrs posted by rex

Caustic Soda tank

I want to build a degreasing tank using Caustic Soda (aka Sodium Hydroxide or Lye) as the active agent. I am already aw...
22 comments posted 21yrs
posted by rhull
22 comments posted 21yrs posted by rhull

OT - Battery Backups

Well, the lights just flicked off in the house and so did my computer so I guess the batteries in my APC Back UPS are d...
16 comments posted 21yrs
posted by none
16 comments posted 21yrs posted by none