⏣ General Metalworking

30778 Threads Posts
to

Brake rotor turning

There was a thread recently about turning Rotor on a small lathe. I turn a set of front rotor from my 1990 Subaru befor...
16 comments posted 22yrs
posted by Billcotton
16 comments posted 22yrs posted by Billcotton

Harbor Freight cutter grinder question

I'm considering the purchase of a Harbor Freight 45707 Universal Cutter Grinder. Wholesale Tool has what appears to be...
0 comments posted 22yrs
posted by admin
0 comments posted 22yrs posted by admin

Anyone heard of a "tommy gage"?

I bought a populated machinist's rollaway once. It has one drawer in which live a set of round "space blocks" which can...
9 comments posted 22yrs
posted by grant
9 comments posted 22yrs posted by grant

Lathe Help

I picked up a used medium size hobby type lathe but the tooling is the wrong size. The bit is about .045" above the cen...
13 comments posted 22yrs
posted by vcc1962
13 comments posted 22yrs posted by vcc1962

Replacement for my old Sheldon?

Looks like my old 11X40 Sheldon has finally gotten to the point that in order to keep my business going, I will have to...
6 comments posted 22yrs
posted by gmasterman
6 comments posted 22yrs posted by gmasterman

Bi metal (thermostat metal) question

I need some thermostat metal in sheet form. I have a hard time finding a US producer. Also does anyone know where to fi...
7 comments posted 22yrs
posted by outhouse
7 comments posted 22yrs posted by outhouse

For you telescope fans

Building the LBT--Large Binocular Telescope. http://medusa.as.arizona.edu/lbto/teleindex.html Tons of photos from start...
2 comments posted 22yrs
posted by DoNotSpamthegoat4
2 comments posted 22yrs posted by DoNotSpamthegoat4

OT: Sweetest Day (some metalworking content)

She just looked at the 14k earrings like they were junk. Gone are the days when I could have bent a rusty nail into a ri...
0 comments posted 22yrs
posted by asdf
0 comments posted 22yrs posted by asdf

brass brazing/soldering

I'm looking for a mid temperature (700-800 deg F) brass (muntz & 360) solder or braze alloy with 15 kpsi or better tens...
6 comments posted 22yrs
posted by grants2
6 comments posted 22yrs posted by grants2

Miller mig welder 25

I have a student in autobody selling what I believe to be a miller 25 mig welder . anybody have any ideas its performan...
2 comments posted 22yrs
posted by eginsberg
2 comments posted 22yrs posted by eginsberg

Anyone here into "punkin' chunkin"?

On one of the cable channels last winter I saw a program about a punkin' chunkin' competition held in Morton, Illinois....
13 comments posted 22yrs
posted by gunluvver2
13 comments posted 22yrs posted by gunluvver2

Jacobs #2 taper setup

OK this is a stupid question however I don't know the answer so here goes. Picked up another tapmatic unit that has a J...
1 comments posted 22yrs
posted by ebay
1 comments posted 22yrs posted by ebay

Another tool ID needed XV

Just posted some more photos, I'm not sure what numbers 155 and 159 are: http://puzzlephotos.blogspot.com/
11 comments posted 22yrs
posted by rhvp65
11 comments posted 22yrs posted by rhvp65

D1-4 chuck mount fit?

I got a lathe with a D1-4 mount on the headstock. Is there a spec. for how close the back of the chuck comes to the spi...
9 comments posted 22yrs
posted by KLMoffett
9 comments posted 22yrs posted by KLMoffett