⏣ General Metalworking

30778 Threads Posts
to

what are 7mf 1500 volt caps good for?

Ive got around a dozen 7mf 1500 volt capacitors. What are they good for? Anyone need them? Gunner It's not unwise to re...
26 comments posted 22yrs
posted by gunner
26 comments posted 22yrs posted by gunner

OT Five Gallon Bucket Fly Traps

>Five Gallon Bucket Fly Traps > >http://www.sonic.net/~dakidd/Horses/FlyTrap/index.html> > > > >caveat lector > >Halcit...
4 comments posted 22yrs
posted by gunner
4 comments posted 22yrs posted by gunner

Looking for parts for a Jet PBY 1024 Lathe

I am looking for a source for parts for my wife's lathe, yup, she bought it from Boeing Surplus and uses it weekly. It...
2 comments posted 22yrs
posted by Eagle_view
2 comments posted 22yrs posted by Eagle_view

7x12 Enco Turnpro bandsaw review

Finally had a chance to get my new 7x12 Enco Turnpro band saw ready and use it. First thing I did was change the oil as...
1 comments posted 22yrs
posted by asdf
1 comments posted 22yrs posted by asdf

Opinions on Tenryu Cermet blades for worm saws

Wondering if anyone out in RCM land has tried these blades? They're supposed to cut easier and last longer when used wi...
0 comments posted 22yrs
posted by rchamberlain
0 comments posted 22yrs posted by rchamberlain

A Tylenol moment

http://images.ibsys.com/2004/0726/3578104.jpg LOS ANGELES -- Six nails embedded in the skull of construction worker Isi...
13 comments posted 22yrs
posted by gunner
13 comments posted 22yrs posted by gunner

OT - AC Fan motor problem

I don't know what other group to post this in, but this the kind of group where I'm likely to find an answer. If it wer...
4 comments posted 22yrs
posted by GeoLane_NOSPAM_
4 comments posted 22yrs posted by GeoLane_NOSPAM_

Cutting off thin flange under a stainless sink?

I bought a used stainless sink and the four flanges underneath (used to bolt the sink to the countertop) are half-ruste...
11 comments posted 22yrs
posted by mbrooks
11 comments posted 22yrs posted by mbrooks

Plama cutter on copper sheet

Hello all, I'm considering the purchase of a plasma cutter to cut complex shapes from copper sheet. Thickness range of...
7 comments posted 22yrs
posted by tecolson
7 comments posted 22yrs posted by tecolson

Anyone recognize this 1890 fire engine?

I'm scanning and archiving hundreds of family slides, most taken between 1955 and 1964. No family is left alive to iden...
1 comments posted 22yrs
posted by janders
1 comments posted 22yrs posted by janders

leather belt splice

I've got to replace the leather drive belt on my old South Bend lathe. I want to use a skived glue joint for the splice,...
20 comments posted 22yrs
posted by william.hopcraft
20 comments posted 22yrs posted by william.hopcraft

Looking for 17" x 17" refridgerator

Like a bar type, but so far smallest Ive found is 19". 12v would be good, can live w/120v. Thank gary
3 comments posted 22yrs
posted by lakemcd
3 comments posted 22yrs posted by lakemcd

Cadillac Height Gage information?

I have a Cadillac Height Gage, PLA-CHEK, 12". Beyond anything obvious are there any specs that need to be checked for pr...
2 comments posted 22yrs
posted by rwatson767
2 comments posted 22yrs posted by rwatson767

CNC 'sand unreliable power

I've been trying to convince the boss we need a CNC mill. We are located in the Ozarks in Arkansas and have unreliable...
20 comments posted 22yrs
posted by clannorm
20 comments posted 22yrs posted by clannorm