⏣ General Metalworking

30778 Threads Posts
to

WTT - 1-7/8 x8 backplate for 1-1/2x8 backplate

Hello all. I'm interested in trading one lathe chuck back plate for another. I have a backplate that comes off a No 400...
4 comments posted 22yrs
posted by dvandam
4 comments posted 22yrs posted by dvandam

A question about a Centec mill

I asked this question over on uk.rec.models.engineering but got no response at all. I've just installed a Centec 2B wit...
3 comments posted 22yrs
posted by binswood
3 comments posted 22yrs posted by binswood

You guys and gals are the best!

I ask a question and I get so many great responces... I've even been able to give a few answers. There sure is a lot of...
7 comments posted 22yrs
posted by q
7 comments posted 22yrs posted by q

Chopper Frame Blueprints

I have a set of Chopper Frame & Jig Blueprints for sale. 7 plans, all dimensions and angles are included. I put a page...
1 comments posted 22yrs
posted by canadian_welder
1 comments posted 22yrs posted by canadian_welder

Engine Hoist

Anybody want to trade a set of engine hoist plans for a set of engine stand plans? Let me know, they are in .pdf format....
9 comments posted 22yrs
posted by berteileenplank
9 comments posted 22yrs posted by berteileenplank

Nickel (not chrome) plating

(Some) older bicycle parts are referred to in the literature of the time as "nickel-plated". Whenever I have asked the...
19 comments posted 22yrs
posted by jtaylor
19 comments posted 22yrs posted by jtaylor

VFD question

OK, I finally acquired a Siemens VFD for use with my lathe and mill. I've seen several posts about not putting a forwar...
4 comments posted 22yrs
posted by SF2727K
4 comments posted 22yrs posted by SF2727K

1 to 3 phase converter question

Built a 5hp idler 3 phase converter with start and tuning capacitors. I did not have proper start capacitor so I used a...
8 comments posted 22yrs
posted by cliftonbel
8 comments posted 22yrs posted by cliftonbel

Vacation pics

If you're wondering where I had been the last week, we (the family) flew to LA then drove a rental to Fresno. From ther...
3 comments posted 22yrs
posted by tmoranwms
3 comments posted 22yrs posted by tmoranwms

OT- We're off!

SWMBO and I are winging down to Orlando this afternoon for a long overdue bit of R&R in Orlando where we'll celebrate o...
2 comments posted 22yrs
posted by jwisnia
2 comments posted 22yrs posted by jwisnia

Home built gun bluing tanks?

Anyone have any links to info on building gun bluing tanks and bluing at home, stainless tanks or otherwise? I have done...
13 comments posted 22yrs
posted by tackdrvr
13 comments posted 22yrs posted by tackdrvr

OLD-OLD Machine

This old machine was sitting in a small museum in Kansas--The curved piece that is perforated with holes was apparently...
2 comments posted 22yrs
posted by wassbiplane
2 comments posted 22yrs posted by wassbiplane

Advice Please: Bending Steel Strap

I picked up some 1/8" steel strap from Home Depot that is about 1-1/4" wide. It has holes in it about every inch or so...
8 comments posted 22yrs
posted by Searcher7
8 comments posted 22yrs posted by Searcher7

Joining aluminum and sainlessl?

I am going to make a fairly large fishing gaff from some of my extensive scrap box. Trying to keep it as light as possi...
7 comments posted 22yrs
posted by gashmore3
7 comments posted 22yrs posted by gashmore3

Hollow mill

I have to make 1000 non stock 3/16 dia screws 1.5 inchs long they have a head on them so i have to make them out of 5/1...
7 comments posted 22yrs
posted by tlkallam8
7 comments posted 22yrs posted by tlkallam8