⏣ General Metalworking

30778 Threads Posts
to

I DID IT! CNC RETROFIT (long)

I finally got the old CNC running with a new control. Maybe some of you have seen AJAX advertised in HSM. Well, it turn...
4 comments posted 22yrs
posted by etpm
4 comments posted 22yrs posted by etpm

making fillet weld with oxyacet?

Hi all Is there some secret to make fillet welds with gas? I can never melt the root of the joint, and if I get enthusi...
2 comments posted 22yrs
posted by tharkaduso
2 comments posted 22yrs posted by tharkaduso

Laminated Hadfield steel source

Looking for an ~.5mm lamination of Hadfield steel applied to one surface of an inexpensive steel substrate about 1/4" t...
0 comments posted 22yrs
posted by E_John_WilsonNoJunk
0 comments posted 22yrs posted by E_John_WilsonNoJunk

silver solder cast iron?

My neighbor asked me to repair a linkage bar from a vintage printing press. It is about 3" long, 1" x 3/4" made of cast...
14 comments posted 22yrs
posted by engineman1
14 comments posted 22yrs posted by engineman1

What causes rubber bands to deteriorate?

What causes rubber bands to deteriorate? I can tell the air has something to do with it, because the rubber bands down i...
28 comments posted 22yrs
posted by c.magnuson
28 comments posted 22yrs posted by c.magnuson

Lathe indexable tool holders

Hello, I have been looking to purchase indexable tool holders for use with my 14X40 lathe. The selection is quite vast...
11 comments posted 22yrs
posted by filister
11 comments posted 22yrs posted by filister

Bearing drag

I'm constructing a homebrew anemometer and on my first try used a new sealed bearing. Unfortunately there seems to be t...
19 comments posted 22yrs
posted by nodamned
19 comments posted 22yrs posted by nodamned

jigs and fixtures

I am teaching "Design of Jigs, Fixtures and press tools". For Jig design I am referring "jig and Fixture design" by Edw...
2 comments posted 22yrs
posted by ilamathibala
2 comments posted 22yrs posted by ilamathibala

240V from a 3 phase main ?

I'm looking to rent industrial space for hobby use and have looked at a few buildings. I was pleasantly surprised to fi...
67 comments posted 22yrs
posted by REMOVETHISacllee
67 comments posted 22yrs posted by REMOVETHISacllee

Sheldon KS type lathe questions

I had a quick look at an old lathe the other day in a shop where I am selling some equipment for the owner. The lathe i...
0 comments posted 22yrs
posted by sam.fest
0 comments posted 22yrs posted by sam.fest

Precise Anodizing

I am looking for a source for some precise anodizing. In particular I am needing to make some watch parts to restore a...
2 comments posted 22yrs
posted by infiniteloop
2 comments posted 22yrs posted by infiniteloop

melting aluminum cheaply

I would like to melt a few old (but clean) pistons to pour into the heat crossover passage on a cast iron cylinder head...
18 comments posted 22yrs
posted by CC
18 comments posted 22yrs posted by CC

watertight bearings

I'm interested in trying to make one of these: http://www.ukam.com/anglegrinder_water_swivel.html Mostly because of the...
14 comments posted 22yrs
posted by jwilson
14 comments posted 22yrs posted by jwilson

Fanuc EHPMs & EMC

(Was: "Re: OT Environmentalists may be in deep Kimchee") >> BTW, Welcome to the swamp ... . > >Thanx mate. > >I have be...
1 comments posted 22yrs
posted by Clhuprich
1 comments posted 22yrs posted by Clhuprich