⏣ General Metalworking

30778 Threads Posts
to

Can you?

Can you connect a 220 volt 3 phase 15 horse VFD to 220 Volt single phase mains then drive a 550 volt 3 phase 5 horse mi...
4 comments posted 22yrs
posted by ca.donaldson
4 comments posted 22yrs posted by ca.donaldson

[Sort of OT] Do trees grow up?

I mean, the trunk part. Just put of a clothesling and the far end is attached to an eyehook in the trunk of a medium-si...
12 comments posted 22yrs
posted by jtaylor
12 comments posted 22yrs posted by jtaylor

one more electrical question

Thanks for all the answers on running 3phase over to the middle of my shop floor. One more question. Actually 2 more 1)...
8 comments posted 22yrs
posted by ivan
8 comments posted 22yrs posted by ivan

DoAll verticle bandsaw

I just purchased a V3813 model with a few minor faults. The air line hose has deteriorated and the speed indicator cabl...
1 comments posted 22yrs
posted by good2b
1 comments posted 22yrs posted by good2b

OT-Cats

Dear Cats: When I say to move, it means go someplace else, not switch positions with one another so there are still thr...
28 comments posted 22yrs
posted by gunner
28 comments posted 22yrs posted by gunner

Free old Studer od grinder

I have a studer od grinder 8 x 20 inch swiss made ( model # rhu 500) i need to scrap it.I don't want to pay the $100 to...
0 comments posted 22yrs
posted by tlkallam8
0 comments posted 22yrs posted by tlkallam8

Hardinge BB4 Questions

I have ran across an old mill I'm not familiar with. The pic on the net looks interesting. Are they very usuable due to...
5 comments posted 22yrs
posted by mlogical
5 comments posted 22yrs posted by mlogical

This Old House

Why did they get a new STAR ? Thanks Ray
14 comments posted 22yrs
posted by smuel10363
14 comments posted 22yrs posted by smuel10363

Cutting Speed derivation

Somewhere, over the years, it seems I picked up some sense of what cutting speed is. However, when asked 'what is cutti...
32 comments posted 22yrs
posted by hel511
32 comments posted 22yrs posted by hel511

Mythbusters and the surplus store

Last night on Mythbusters, the 2 guys went to a surplus store in the SF bay area. I've never seen this store and was won...
3 comments posted 22yrs
posted by jstewart
3 comments posted 22yrs posted by jstewart

gwm rotary ph conv ?

i am hooking up a G W M rotary phase converter, and i am having a problem understanding the wiring diagram. it looks li...
1 comments posted 22yrs
posted by wgalcik
1 comments posted 22yrs posted by wgalcik

Cole vise info

Christmas season score..... Can anyone steer me to some info on a Cole #11 vise? The bottom pivot is broken and it needs...
0 comments posted 22yrs
posted by clittle67
0 comments posted 22yrs posted by clittle67

eBay Scam

Heads up - another "gotcha" eBay scam - as follows: "Dear eBay member # 12674539! It has come to our attention that you...
5 comments posted 22yrs
posted by msoloff
5 comments posted 22yrs posted by msoloff

Sheet metal tool advice sought

I prototype antennas (of my design) in my metalworking shop. Having sheet metal capability is becoming important, and I...
4 comments posted 22yrs
posted by spencer313
4 comments posted 22yrs posted by spencer313

Comments on "Modern" SBL 14" Please?

Hello all: While my '42 10L has served me well, it is quite worn (ways and such), and I have been contemplating somethi...
2 comments posted 22yrs
posted by wallyblackburn
2 comments posted 22yrs posted by wallyblackburn