⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30752 Threads Posts
to

DeWalt charger unstable?

My DW9118 charger emits a loud ~10 KHz audible tone when charging a battery. It didn't use to do that. Anybody else have...
7 comments posted 14yrs
posted by Winston
7 comments posted 14yrs posted by Winston

Setup Sheets

Mastercam's setup sheets suck so bad I use an add-in called X+ I think this better than X+ for Mastercam and is how setu...
3 comments posted 14yrs
posted by jonbanquer
3 comments posted 14yrs posted by jonbanquer

Arch Micro Tools

Who actually has them in stock? Looking for some LB2116 ball end mills.
0 comments posted 14yrs
posted by none
0 comments posted 14yrs posted by none

Best kind of steel for lathe leadscrew?

Hi guys, I am going to have to machine a new leadscrew for a Myford Super 7 I've recently acquired. This existing one i...
10 comments posted 14yrs
posted by orion.osiris
10 comments posted 14yrs posted by orion.osiris

Source for window sealant

I had to remove a broken aluminum window from one of my garage walk doors. I found I could gently pry the frame out of...
24 comments posted 14yrs
posted by lloydspinsidemindspring.com
24 comments posted 14yrs posted by lloydspinsidemindspring.com

horizontal mill bearing

My supermax mill has both a vertical and a horizontal spindle. Unfortunately the outboard spindle support for the horiz...
4 comments posted 14yrs
posted by karltownsend.NOT
4 comments posted 14yrs posted by karltownsend.NOT

Speedi-Sleeve anyone shrink fit an undersize one?

I am dealing with a shaft dia of 1.326 in. The CRC/SKF Speedi-Sleeve does = not have an application for this diameter....
4 comments posted 14yrs
posted by aribertn
4 comments posted 14yrs posted by aribertn

Lets roll!

During the Colorado shooting, wasn't there one person who said "Oh, well, I'm dead anyway" and charged, and tackled the...
492 comments posted 14yrs
posted by cayoung61***spamblock
492 comments posted 14yrs posted by cayoung61***spamblock

Question about "right to bear arms"

When did the right to bear arms to protect the state from invasion, become the right to bear arms to protect the person/...
23 comments posted 14yrs
posted by noonehome
23 comments posted 14yrs posted by noonehome

Making Your Own Helical Couplers

How would you tackle it. I finally got around to putting a motor on one of my rotary chucks and hooking it to a control...
5 comments posted 14yrs
posted by alarm_wizard
5 comments posted 14yrs posted by alarm_wizard

FS -- Grob Model ML 16 inch bandsaw

Not identical, but looks like this http://vintagemachinery.org/photoindex/detail.aspx?id=11746 and it comes with manual....
10 comments posted 14yrs
posted by ignoramus22200
10 comments posted 14yrs posted by ignoramus22200

Rotary airless paint sprayer?

I've got a stunningly bad track record with paint sprayers. They generally clog up almost instantly and just fail to pe...
18 comments posted 14yrs
posted by Winston
18 comments posted 14yrs posted by Winston

lathe operation question

lathe operation question time. I have a very small lathe (sherline, 17" bed) I need to turn some "longer" items in it b...
7 comments posted 14yrs
posted by presence
7 comments posted 14yrs posted by presence

Dayton 4Z140 - Gloat

Grainger price (not logged in) shows as $242.50. Ebay shows them for $75 to $180. I got 4 of them along with 3 12 volt...
4 comments posted 14yrs
posted by none
4 comments posted 14yrs posted by none

New CADCAM Technology Leaders Group On LinkedIn

I started a new group on LinkedIn for the discussion of leading edge CADCAM technology: http://tinyurl.com/7rhka97 No pe...
2 comments posted 14yrs
posted by jonbanquer
2 comments posted 14yrs posted by jonbanquer