⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Give away - Iomega Zip drive

Not sue if I posted this before, but I have a Iomega Zip drive and a couple disks to give away. First one to holler can...
22 comments posted 17yrs
posted by goo1959
22 comments posted 17yrs posted by goo1959

OT more than virus protection

To wet to work outside, too early for shop season. So, both office computers were just crawling. I put in new hard driv...
27 comments posted 17yrs
posted by karltownsend.NOT
27 comments posted 17yrs posted by karltownsend.NOT

Total War!

http://www.break.com/index/the-great-office-war.html
0 comments posted 17yrs
posted by gunner
0 comments posted 17yrs posted by gunner

ex-propane tank jack o'lantern

something i made. weak metalworking content. http://www.frontiernet.net/~wwixon/jacko'lanterns.jpg
5 comments posted 17yrs
posted by wwixon
5 comments posted 17yrs posted by wwixon

Ping: Dave

For some reason Thunderbird randomly refuses to send my replies to the group. Regarding the bolts, I'm pretty sure I go...
1 comments posted 17yrs
posted by fusion640
1 comments posted 17yrs posted by fusion640

Interesting proposal

HR 615 On Tuesday, the Senate health committee voted 12-11 in favor of a two-page amendment, courtesy of Republican Tom...
2 comments posted 17yrs
posted by cavelamb
2 comments posted 17yrs posted by cavelamb

Are there many treaters?

Last year I got about 50, and it was pretty even between boys and girls. By 7:15 tonight, 18 boys and 8 girls. Maybe eve...
12 comments posted 17yrs
posted by cayoung61**spamblock##
12 comments posted 17yrs posted by cayoung61**spamblock##

Turning common pipe

How can I turn 1.5" pipe and get a decent finish. Need to make a sleeve for a golf cart clutch and 1.5" pipe is close t...
9 comments posted 17yrs
posted by gmasterman
9 comments posted 17yrs posted by gmasterman

Interesting Bay Bridge Failure Article

Hi all, A friend sent this, thought the group would like to see it. In particular, note the rust accumulation in the 'E...
6 comments posted 17yrs
posted by spam
6 comments posted 17yrs posted by spam

15 hp 3P motor run on 10 HP Desco Panel?

Please forgive my ignorance but in the interest of possibly saving money, can I use the 15 HP motor I already have with...
4 comments posted 17yrs
posted by americansun
4 comments posted 17yrs posted by americansun

Anyone Speak Both English and French

...And want to quote a job in Quebec to a potential customer of mine as a distributor? I'll make you a distributor of s...
6 comments posted 17yrs
posted by autodrill
6 comments posted 17yrs posted by autodrill

Wells Iggy & me

I just scored a Wells mill. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250516918729&ssPageName=ADME:B:EOIBSA:US...
15 comments posted 17yrs
posted by karltownsend.NOT
15 comments posted 17yrs posted by karltownsend.NOT

Taper angles

I have a small woodworking router plane that has a vertical round rod carrying the blade on the lower end. The clamping...
8 comments posted 17yrs
posted by e_john_wilson.no.spam.
8 comments posted 17yrs posted by e_john_wilson.no.spam.