⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Looking for "shaft coupler"

I want to run a gear reducer with a bench grinder motor.The motor has a "1/2-inch shaft threaded" and the gear reducer...
9 comments posted 19yrs
posted by lopnerx
9 comments posted 19yrs posted by lopnerx

Another use for rare earth magnets

http://www2.citytel.net/~solar/milledrillpage.html Scroll down to item #5
28 comments posted 19yrs
posted by QYNLZMTZBOQZ
28 comments posted 19yrs posted by QYNLZMTZBOQZ

Precision taper/polishing job

I've got a design working up that calls for a tapered cavity (for pressing pyrotechnic compositions). This is a new ski...
30 comments posted 19yrs
posted by lloydsp
30 comments posted 19yrs posted by lloydsp

lathe cherry tool?

hey... I need to cut a cone shaped hole about an inch into the end of a brass rod about 1/2 dia.. I figure I need to ge...
3 comments posted 19yrs
posted by waldhorn
3 comments posted 19yrs posted by waldhorn

OT - Value of a used car as parts

Is it humanly possible to buy a used car and part it out for parts, and make any money? I don't see how this is possibl...
10 comments posted 19yrs
posted by stone75
10 comments posted 19yrs posted by stone75

LeBlond Regal 13" Spindle Threading

I need the spindle threading for a LeBlond Regal 13". Serial number if that matters is B4854. I am replacing the conven...
15 comments posted 19yrs
posted by rwatson767
15 comments posted 19yrs posted by rwatson767

Powermatic 1140B chuck removal

I have recently acquired a Powermatic 1140B bench drill press. Everything seems to be working on it and the price was p...
9 comments posted 19yrs
posted by steve
9 comments posted 19yrs posted by steve

fishmouth cutting (Ernie?)

I had a major hard drive crash and lost my software for printing out fishmouth cutting templets and can't seem to locat...
15 comments posted 19yrs
posted by mcrump1
15 comments posted 19yrs posted by mcrump1

220-440 3 phase open delta?

Suppose I have two single phase transformers, call them A and B, each configured to step down 440 to 220. Ignoring any...
9 comments posted 19yrs
posted by grant
9 comments posted 19yrs posted by grant

What does this tool holder fit?

I bought a box of stuff at auction - specifically for the B&S tooling it contained. Well I ended up with several other...
4 comments posted 19yrs
posted by grice
4 comments posted 19yrs posted by grice

Cincinatti Horizontal mill

Hi, I am new to this group and thought someone out there might be able to help me. I have a cincinatti #2 MI horizontal...
9 comments posted 19yrs
posted by mrogers
9 comments posted 19yrs posted by mrogers

Where's Millwrightron now?

With all this talk about retail workers being abused, where's Millwrightron with his union soapbox? I'll tell you where...
1 comments posted 19yrs
posted by nospam
1 comments posted 19yrs posted by nospam

Rare earth magnet question

I have been reading about searching for meteorites. I live in a good area for it, with lots of open desert and few plan...
21 comments posted 19yrs
posted by SurDO2Diver
21 comments posted 19yrs posted by SurDO2Diver

Opinions on Grizzly lathe/mill combos

I'm thinking of getting a lathe/mill combo. Can anyone give their opinions on these two from Grizzly http://www.grizzly...
17 comments posted 19yrs
posted by paulinlapine
17 comments posted 19yrs posted by paulinlapine

A little splurge (to be used for the die cart)

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=120106010025 To be used for this cart: http://igor.chudov.com/projec...
16 comments posted 19yrs
posted by ignoramus15609
16 comments posted 19yrs posted by ignoramus15609