⚡ Welding Forums

Tested my TIG inverter bridge under full power

Just wanted to say that after slight snubber circuit modifications (more below), I was able to test my bridge under ful...

28 comments posted 20yrs

posted by ignoramus29530

28 comments posted 20yrs posted by ignoramus29530

Kicking Myself!

Well, I did a good one today. When moving the argon bottle for my TIG welder I knocked it over and, of course, broke th...

6 comments posted 20yrs

posted by desmithe

6 comments posted 20yrs posted by desmithe

Eletrolytic Rust Removal Question

I am trying to use a leftover AC/DC adapter(s) to power an electrolytic rust removal rig I built. It works fine on a sm...

33 comments posted 20yrs

posted by jredmond

33 comments posted 20yrs posted by jredmond

Pictures -- My TIG inverter plugged into the actual welder

[a small introduction, I am working on a solid state advanced square wave inverter to add to my DC tig welding machine]...

11 comments posted 20yrs

posted by ignoramus10725

11 comments posted 20yrs posted by ignoramus10725

computer question

Well, I can't figure it out, so I will ask youse guys ......... When I bring up my home page, or ebay, or lots of sites...

7 comments posted 20yrs

posted by deserttraveler

7 comments posted 20yrs posted by deserttraveler

Sanitary Weld Layout

Hello all, Simple pipe fitting question. I am having a sanitary clover tank ferrule welded to a tank. There are 3 possi...

4 comments posted 20yrs

posted by Mkulikow

4 comments posted 20yrs posted by Mkulikow

Inverter efficiency ie. Miller vs. Thermal Arc

I thought I had made up my mind about a new inverter TIG and decided on the ThermalArc 185 over the much more expensive...

1 comments posted 20yrs

posted by rick.fetters

1 comments posted 20yrs posted by rick.fetters

Newbie asks.........

Any good website(s) that clearly explain the best way to braize metal using MAPP gas? TIA. John Locke

2 comments posted 20yrs

posted by john.locke

2 comments posted 20yrs posted by john.locke

TIG over Black Oxide

A customer is requesting that the bolts in his assembly be TIG welded in place to make them permanent. I've not been ab...

1 comments posted 20yrs

posted by mhillDELETE

1 comments posted 20yrs posted by mhillDELETE

SIP Migmate Super wiring diagram?

I have an older (15 years??) SIP Migmate Super (made in England) that quit talking to me. It clicks the relay, that's a...

3 comments posted 20yrs

posted by spamless

3 comments posted 20yrs posted by spamless

Century/Powermate mig repair

Hi all, I bought a used mig welder Powermate and it seemed to work ok. after welding for a few hours it made a grinding...

6 comments posted 20yrs

posted by plepper

6 comments posted 20yrs posted by plepper

trailer plans

anyone have plans for a trailer of some type? want to build at 5ftx10ft one. thanks

10 comments posted 20yrs

posted by brian_santoro

10 comments posted 20yrs posted by brian_santoro

Wanna-Be Weld needs help!!!

Well, first let me say that I have enjoyed reading all of the posts over the past week. I have learned so much from man...

3 comments posted 20yrs

posted by shallowrunner2002

3 comments posted 20yrs posted by shallowrunner2002

Looking for Tweco #2 Mig Gun parts diagram/user manual

Hi, Very new to welding (haven't even run the 220 for my Millermatic 175 yet). I'm looking for a parts diagram and (if...

2 comments posted 20yrs

posted by Chubster

2 comments posted 20yrs posted by Chubster

Gas Mixer question

Hi, Does anyone know where I could find a diagram / schematic / description etc. of the innards of a 2 gas proportional...

0 comments posted 20yrs

posted by 1313

0 comments posted 20yrs posted by 1313