⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6251 Threads Posts
to

Miller 250 Question ???

I recently ran across a Miller 250 for sale for what seems like a reasonable price. I have a couple questions though. D...
2 comments posted 17yrs
posted by nospam
2 comments posted 17yrs posted by nospam

cebora parts

I have a 140 Mig mig by Cebora,I need the heat control switch(0-4),been told this is also the same as a Daytona mig,mac...
0 comments posted 17yrs
posted by VonJason
0 comments posted 17yrs posted by VonJason

dumb question on compressor displacement cfm

One of my compressors has bore 4" stroke 3-1/2" two cylinders (single stage) and can run at 900 rpm max. I am trying to...
46 comments posted 17yrs
posted by grantNOSPAM
46 comments posted 17yrs posted by grantNOSPAM

Slight welding content

--Put up some photos of my calliope project. Had fun welding various bits, too. http://www.flickr.com/photos/38392448@N0...
3 comments posted 17yrs
posted by steamer
3 comments posted 17yrs posted by steamer

Rebar rod

6010 or 7018. Going to use on 1/2 and 3/4 rod for garden forms, and to hold up slabs of rocks for water features. Outdo...
2 comments posted 17yrs
posted by oldfart
2 comments posted 17yrs posted by oldfart

gas engine electrical questions

I have a Wisconsin THD 18hp gas engine. It has serial number 2942748. In the manual it says, "Beginning with engine ser...
18 comments posted 17yrs
posted by grantNOSPAM
18 comments posted 17yrs posted by grantNOSPAM

Multiplaz-2500 M

Hi Guys, I'm not a welder, although I have attempted to play one at home. (stick welding with an old Craftsman welder)...
4 comments posted 17yrs
posted by amdx
4 comments posted 17yrs posted by amdx

Rear frame fabrication

Hi guys I?m working on a 67' ChevII and I?m doing a custom 3 link on it. Im replacing the frame rails and adding a cros...
0 comments posted 17yrs
posted by barbara.thomas45_at_gmail_dot_
0 comments posted 17yrs posted by barbara.thomas45_at_gmail_dot_

soldering aluminum

I need to solder to an aluminum tube for an electrical connection. I was hoping I could tin the Al and then latter sold...
15 comments posted 17yrs
posted by jimmie68
15 comments posted 17yrs posted by jimmie68

O-A flame pics?

I'm doing a quickie lesson on OA cutting. Anyone got some nice pics of the inner and outer cones for adjusting an O-a t...
6 comments posted 17yrs
posted by spamless
6 comments posted 17yrs posted by spamless

Vibratory Stress Relief

OK, Everyone have a good laugh. Now you've calmed down: Does anyone have experience of this process either during or po...
3 comments posted 17yrs
posted by Invalid
3 comments posted 17yrs posted by Invalid

140A Mig Welder: 1/8" aluminum plate Pure Argon ?

I recently got my first welder. I have formed a couple of fenders for a trailer I'm refurbishing and need to weld a "ha...
5 comments posted 17yrs
posted by NoSpam
5 comments posted 17yrs posted by NoSpam

Plasma cutter flow rate requirement

I am buying a plasma cutter, and my welding supplier is pushing the Miller 375. Very light, small machine, but it does...
25 comments posted 17yrs
posted by sasrbk
25 comments posted 17yrs posted by sasrbk