⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Ferrari scale model

You may have seen this before, but I think it's worth a second look: http://youtube.com/watch?v=l3NVJ4pEFuY Pierre Scer...
8 comments posted 19yrs
posted by fake
8 comments posted 19yrs posted by fake

Making a parallel test bar

I need a parallel test bar to center workholders on my grinder and to properly level my lathe. I've been looking for on...
6 comments posted 19yrs
posted by grice
6 comments posted 19yrs posted by grice

Sticky mag chuck ideas?

Hi all, I got ahold of a small PM mag chuck a while back that looks like it will go nicely with my T&C grinder. It work...
8 comments posted 19yrs
posted by alanganes
8 comments posted 19yrs posted by alanganes

What is it? CXLVII

http://puzzlephotos.blogspot.com/ Rob
17 comments posted 19yrs
posted by rhvp67
17 comments posted 19yrs posted by rhvp67

Need advise about buying Millrite mill

There is local guy selling his Millrite mill for $1300. I haven't seen it but he is saying it's tight. Any word of advi...
7 comments posted 19yrs
posted by alexkuzn
7 comments posted 19yrs posted by alexkuzn

Contour Marker

Anyone have the instruction sheet for thos contour marker. I lost mine. BGP Alberta, Canada http://www.jacksonproducts.c...
3 comments posted 19yrs
posted by bplank
3 comments posted 19yrs posted by bplank

diamond tile cutters

Has anyone tried cutting metal with the inexpensive home depot diamond tile cutters? The table saw type.
9 comments posted 19yrs
posted by shabtai
9 comments posted 19yrs posted by shabtai

Four post car lift

I'm looking to buy a 4-post automotive lift. Anybody have an opinion on brands and accessories? Thanks.
15 comments posted 19yrs
posted by mcgeepby
15 comments posted 19yrs posted by mcgeepby

Wire rope question

I need to buy a new wire rope for a griphoist. They say only their special four-strand wire rope should be used. With a...
0 comments posted 19yrs
posted by devnull
0 comments posted 19yrs posted by devnull

Anodizing question

I need to make a couple dozen .940" aluminum cylinders .940" long, 6061-T6 and coat them with a reasonably durable flat...
20 comments posted 19yrs
posted by spamless
20 comments posted 19yrs posted by spamless

How to round corners on end mill

I need to round corners on 3/4" end mill to about 1/8" diam. Can you recommend me any particular way to do it? Does anyo...
10 comments posted 19yrs
posted by alexkuzn
10 comments posted 19yrs posted by alexkuzn

layout question - notching tubing

I have a two part fit-up / fabrication question... I have a 24 inch diameter drum, and I want to join a 5 inch pipe to...
7 comments posted 19yrs
posted by rbce2003
7 comments posted 19yrs posted by rbce2003

Best price HF 55lbs Anvil

What is the best price for HF 55lbs Anvil Lot no. 806. HF says $49.99 reg price, Sale $29.99 - I have a notion that it...
19 comments posted 19yrs
posted by nomail
19 comments posted 19yrs posted by nomail

Acura collets interchangeable?

I have an Acura-Mill collet holder and one collet. I would like to buy some additional collets. Acura-Flex and Acura-Gr...
0 comments posted 19yrs
posted by grice
0 comments posted 19yrs posted by grice