⏣ General Metalworking

30778 Threads Posts
to

Maraged steel?

I ran across some of this in a scrap pile. What is maraged steel m300? What would be a good use for it. I have a piece a...
2 comments posted 21yrs
posted by pshelc
2 comments posted 21yrs posted by pshelc

Low strength belleville washers

Anyone know of a source of really thin / low thrust belleville washers? ...I'd like to find some about the same strength...
5 comments posted 21yrs
posted by news.ind.net.spamtrap1
5 comments posted 21yrs posted by news.ind.net.spamtrap1

Looking for Colorado Fabricator

I am looking for a fabricator in the Denver, Colorado area that can cut, bend and weld .063 sheet aluminum. Does anyone...
2 comments posted 21yrs
posted by nospam
2 comments posted 21yrs posted by nospam

Carbide Bur Metal Working Cutting Tools

found some nice high quality carbide burs online and i just thought i would recommend them to others out there http://ww...
0 comments posted 21yrs
posted by greenlasergroup
0 comments posted 21yrs posted by greenlasergroup

return spring for rockwell quill

There is no spring on the quill of my rockwell vertical mill. I find this so annoying because the quill has dropped a f...
10 comments posted 21yrs
posted by cas
10 comments posted 21yrs posted by cas

FA Nice little surface grinder ( ebay )

Nice little sanford surface grinder : http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=45021&item=3865699931&rd=1...
8 comments posted 21yrs
posted by azotic
8 comments posted 21yrs posted by azotic

OT- What's this sand in cartridge fuses?

Can someone confirm what the "sand" in typical cartridge fuses is put there for? I suspect it probably has to do with q...
23 comments posted 21yrs
posted by jwisnia
23 comments posted 21yrs posted by jwisnia

*Another* machine for Harold!! :)

Boy, this Lagun sure has a lot of spots to oil on the table: Honstly I think I'd rather have that southbend to clean up....
18 comments posted 21yrs
posted by jim_member
18 comments posted 21yrs posted by jim_member

OT: Transparent tubing for water torch

The metal content is tenuous, but its for a water torch that I use for brazing and welding very small parts. The water...
3 comments posted 21yrs
posted by binswood
3 comments posted 21yrs posted by binswood

What is it? XLIV

Just posted a few more: http://puzzlephotos.blogspot.com/ Rob
37 comments posted 21yrs
posted by rhvp67
37 comments posted 21yrs posted by rhvp67

recommend a clear coat spray?

I dont have any fancy paints or even an air compressor for that matter, but i dont want my sheetmetal projects to be so...
9 comments posted 21yrs
posted by xdissent
9 comments posted 21yrs posted by xdissent

Ajax / Speedaire compressors any good?

I was about set to buy a new 60-gal / 3hp single-stage Ingersoll-Rand compressor (around $550) when I ran across an ad...
3 comments posted 21yrs
posted by no_spam
3 comments posted 21yrs posted by no_spam

A rusty lathe question

Hello looking at the photo's of the 10L i realized that on the second to last photo under the micro stop there is a L s...
2 comments posted 21yrs
posted by acmarine
2 comments posted 21yrs posted by acmarine

news group broken

can not get any messages on
1 comments posted 21yrs
posted by harolda102
1 comments posted 21yrs posted by harolda102

this newsgroup is broken

something is broke anyway
8 comments posted 21yrs
posted by harolda102
8 comments posted 21yrs posted by harolda102