⏣ General Metalworking

30778 Threads Posts
to

Nomex by the yard?

SWMBO is looking for Nomex fabric for various projects (killer oven mitts, etc.) Apparently no one in the quilting news...
4 comments posted 22yrs
posted by rcook5
4 comments posted 22yrs posted by rcook5

Pony Motor - Was Intnl Crawler

I remember the pony motor on an old D4 Cat we had at the company where I worked summers during college. I'm trying to r...
11 comments posted 22yrs
posted by GeoLane_NOSPAM_
11 comments posted 22yrs posted by GeoLane_NOSPAM_

ESAB/Heliarc 252 question

Greetings all, Well, my trusty ol' 252 is acting up, again. OK, it's not really mine, _technically_ it's my bosses, but...
8 comments posted 22yrs
posted by jimnthem_AT_comcast_DOT_net
8 comments posted 22yrs posted by jimnthem_AT_comcast_DOT_net

metric fastener help needed

I am looking for an M12 X 1.50 pitch 20 or 25 mm hex head bolt in 12.9 specification, and I am starting to believe that...
17 comments posted 22yrs
posted by brian.evans
17 comments posted 22yrs posted by brian.evans

Atlas 10" QC repair

I'm in the middle of trying to get this QC box fixed. In inspection the various pices and figuring out what to order, I...
3 comments posted 22yrs
posted by rex
3 comments posted 22yrs posted by rex

Thread wear advise

Hi all One of my many avocations is making and repairing drums that have natural skin heads. I made a heading jig a few...
35 comments posted 22yrs
posted by mcgillNOSPAM
35 comments posted 22yrs posted by mcgillNOSPAM

Boyer-Shultz question

When I picked up the two Boyer Shultz surface grinders last week, inside one of them was a tackle box with a factory la...
2 comments posted 22yrs
posted by gunnerNOSPAM
2 comments posted 22yrs posted by gunnerNOSPAM

Anyone have a Mooradian?

Table saw. Picked one up at the scrap yard, other than dirty and rusty, and missing a few parts, seems to be in pretty...
1 comments posted 22yrs
posted by Nobody
1 comments posted 22yrs posted by Nobody

OT - Generac generator engines

I've found and old generac propane engine, 4 cylinder, I think it's a 2.6L Does anyone know who makes this engine? I nee...
4 comments posted 22yrs
posted by stone75
4 comments posted 22yrs posted by stone75

What's the best way to bend aluminum

The piece is only about 50cm wide and 40cm high and 4mm thick. It is a bracket . It needs to be bent in a straight line...
13 comments posted 22yrs
posted by runer
13 comments posted 22yrs posted by runer

Lincoln square wave welder question

A fellow offered me a Lincoln square wave TIG welder. About 10-14 yrs old. He replaced all the boards etc..but it still...
5 comments posted 22yrs
posted by gunnerNOSPAM
5 comments posted 22yrs posted by gunnerNOSPAM

Crossbow Plans?

Anybody know of a site on the net that shows how to build a crossbow?
22 comments posted 22yrs
posted by mgoodwinnospam
22 comments posted 22yrs posted by mgoodwinnospam

Expanded metal

Before I go chasing all over town looking for something that may not exist, I thought I would ask here: I looking for a...
9 comments posted 22yrs
posted by Usenet01REMOVE
9 comments posted 22yrs posted by Usenet01REMOVE

Replacement engine for Colemate Generator

I couldn't get the reply to work so I posted this update to my generator project. Search for - Replacement engine for C...
0 comments posted 22yrs
posted by rsnyder187
0 comments posted 22yrs posted by rsnyder187

stainless peg-board-like product?

I once found a piece of flat stainless sheet that had holes punched or drilled into it about 3/16 inch or so, about 1/1...
3 comments posted 22yrs
posted by stone75
3 comments posted 22yrs posted by stone75