⏣ General Metalworking

30778 Threads Posts
to

FA: DIACRO ROLLS - special

Thought a couple people might be interested in this hard to come by set of rolls. http://cgi.ebay.com/ws/eBayISAPI.dll?V...
0 comments posted 22yrs
posted by jjo49
0 comments posted 22yrs posted by jjo49

FS Morse Taper Drill Drivers

I have a bunch of surplus #1 and #2 morse taper drill drivers and tap drivers. No complete sets, but quite a variety of...
0 comments posted 22yrs
posted by mptoolman
0 comments posted 22yrs posted by mptoolman

Discovered New Storage Boxes

This may be an old idea to some of the gun enthusiasts on this newsgroup, but the idea of using plastic ammunition boxe...
2 comments posted 22yrs
posted by mptoolman
2 comments posted 22yrs posted by mptoolman

Book Recommendations?

On topic, which is a switch for me . What book(s) would you recommend? Here are a few I've found either useful, interes...
0 comments posted 22yrs
posted by tquacken
0 comments posted 22yrs posted by tquacken

Upside down Jack Used on Enerpac Hydraulic Presses

Anyone know where to obtain one of these jacks that is used to move the table up and down on most Enerpac H Frame Press...
0 comments posted 22yrs
posted by Sierevello
0 comments posted 22yrs posted by Sierevello

More South Bend lathe questions

Has anybody seen this lathe on E-Bay? I've not seen a South Bend like this, are they any good? http://cgi.ebay.com/ws/eB...
3 comments posted 22yrs
posted by jbm
3 comments posted 22yrs posted by jbm

9" logan change gear bracket

Hello, my name is Domenic Croce and I have a small dilemma that hopefully someone can help me with. Around 12/12/02 I p...
0 comments posted 22yrs
posted by dcroce
0 comments posted 22yrs posted by dcroce

Setting up a shop

What should a shop have in it? To narrow down that question a bit, let me put it this way: Assuming I didn't have any s...
11 comments posted 22yrs
posted by berserker_calm
11 comments posted 22yrs posted by berserker_calm

Ideas needed for take a part joints

As a hobby I make items out of copper and manage to sell a few items a year. I've recently had an inquiry for one of my...
9 comments posted 22yrs
posted by lane_nospam
9 comments posted 22yrs posted by lane_nospam

What is the name of this type of nut?

Hi everyone, I am looking at a manual written in Japanese that explains how to hand a cabinet from the ceiling. I was w...
17 comments posted 22yrs
posted by lepidus
17 comments posted 22yrs posted by lepidus

Williams TEN SPOT Problem

Hi all I have a hard time to figure out what is wrong with my old Williams TEN SPOT pinball. Score board works but "gam...
5 comments posted 22yrs
posted by joku
5 comments posted 22yrs posted by joku

118 vs 135

What factors drive the selection of the drill bit angle? I need to restock on bits and I've always just bought jobber T...
24 comments posted 22yrs
posted by gspaff
24 comments posted 22yrs posted by gspaff

Technical people in China

Just got back from Shanghai in China where I spent 3 weeks as part of my job building medical instruments. We were demo...
5 comments posted 22yrs
posted by deanb
5 comments posted 22yrs posted by deanb

It Don't Add Up

Being a hard-core fan of Doctor Who about ten years ago I set out to make a working sonic screwdriver and did a brillia...
20 comments posted 22yrs
posted by notat
20 comments posted 22yrs posted by notat