⏣ General Metalworking

30778 Threads Posts
to

HELP: Single Point Thread Cutting

I hope somebody has the patience to read through this :-) I am trying to include all the details because I don't know w...
34 comments posted 22yrs
posted by no
34 comments posted 22yrs posted by no

Parting/Grooving Inserts - Brand Specific?

I have a Sandvik parting/grooving tool I picked up at an auction - number is 151.21-16-40. I can tell from the number t...
0 comments posted 22yrs
posted by wallyblackburn
0 comments posted 22yrs posted by wallyblackburn

"Penetrating" Oil

What is this stuff? What makes it more penetrating than any other low viscosity oil? Maybe some solvent/surfactant adde...
9 comments posted 22yrs
posted by tedbennett
9 comments posted 22yrs posted by tedbennett

Pics of "amazing lathe gloat" and questions

See Dropbox for "davis_lathe" and "davis_tools" photos. It's a rather heavy 12x36 machine from around 1910. The headsto...
18 comments posted 22yrs
posted by gto69ra4
18 comments posted 22yrs posted by gto69ra4

A little OT (no metal) but impressive

Maybe some of you iron mongers would like to try: http://www.shamey.com/tooth/tooth.htm
3 comments posted 22yrs
posted by dgriff237
3 comments posted 22yrs posted by dgriff237

Tool gloat

I was at the hardware store (owned by Sears) and I spied some power tools on sale for 50% off. while most of the stuff...
1 comments posted 22yrs
posted by shoaf
1 comments posted 22yrs posted by shoaf

Acetylene tank safety?

I recently bought an acetylene torch and tank which I haven't used yet, but after leaving it in the basement for a few...
35 comments posted 22yrs
posted by servicenospam
35 comments posted 22yrs posted by servicenospam

EPDM rubber adhesive

I'm building a water garden. The liner is 45 mil EPDM rubber. Looks just like an inner tube rubber. Long story short, I...
9 comments posted 22yrs
posted by karltownsend.NOT
9 comments posted 22yrs posted by karltownsend.NOT

Drafting machine (G)

I picked up a marvelous motorized drafting table last week, and got out my old drafting machine to bolt up to it. (Muto...
3 comments posted 22yrs
posted by gunner
3 comments posted 22yrs posted by gunner

OT What is happening to the gun control movement?

>Whither Gun Control? > >Saturday, May 22, 2004 > >By John R. Lott, Jr. > >What is happening to the gun control movemen...
29 comments posted 22yrs
posted by gunner
29 comments posted 22yrs posted by gunner

OT: Strength

>Strength > >Bill Whittle has posted another awe-inspiring essay to his blog that's well >worth the read. It's another...
2 comments posted 22yrs
posted by gunner
2 comments posted 22yrs posted by gunner

bandsaw blades

Alright. I am going to HF to get my bandsaw. I am tired of the chop saw. Noisy. Sparky. Dusty. Dangerous. Every time I...
13 comments posted 22yrs
posted by desertNOtravelerSPAM
13 comments posted 22yrs posted by desertNOtravelerSPAM

Laser on silver plated copper alloy

Hi We intend to use laser to cut and trim semiconductor type of leadframe. Unfortunately, the leadframes we have are al...
3 comments posted 22yrs
posted by spkang
3 comments posted 22yrs posted by spkang

Welder with GFCI question

This might be a stupid question, but if I want to use my welder on a GFCI outlet and have it use the GFCI do I have to...
2 comments posted 22yrs
posted by michaelshaffer
2 comments posted 22yrs posted by michaelshaffer

New tool gloats & questions

I just aquired a few new tools..... A Sheldon EXL 44 and a Unimat 3 lathe/drill press/table saw/sander/ will a bunch of...
2 comments posted 22yrs
posted by polyman
2 comments posted 22yrs posted by polyman