⏣ General Metalworking

30778 Threads Posts
to

Cookie tins

Because I am a packrat ("Don't throw that away! It's METAL!") I have a small collection of those painted cookie tins th...
10 comments posted 22yrs
posted by tedbennett
10 comments posted 22yrs posted by tedbennett

Pictures of moving a good sized lathe

My friend bought a South Bend Series "O" built circa 1928-1930 with a 13" swing and a 60" bed an hour from his house an...
6 comments posted 22yrs
posted by rcbryan
6 comments posted 22yrs posted by rcbryan

wtb "machine tool reconditioning" book

looking for this book has been difficult i only can find it at biax for an inflated prce of $200. any other source out t...
8 comments posted 22yrs
posted by asp3211968
8 comments posted 22yrs posted by asp3211968

Idiot on Ebay (ohojim)

Some idiot called ohojim is really spoiling the ebay experience. I regularly type "lathe" into the search box, to see w...
38 comments posted 22yrs
posted by allenb_deja
38 comments posted 22yrs posted by allenb_deja

How is tube end rolling done?

I'd like to roll the ends of some aluminum tube over toward the inside. The tube is 2" OD with 1/16" wall. I need to do...
3 comments posted 22yrs
posted by spam
3 comments posted 22yrs posted by spam

Air tank safety: Discharge rate and outlet size

I have a couple questions about air receiver safety. I have a 20 gallon ASME carry tank (Grainger 4TK10). It has two 1/...
9 comments posted 22yrs
posted by adam
9 comments posted 22yrs posted by adam

Electolysis & firearms

Was recently lurking and reading the newsgroup and found the electrolysis thread of interest. If it works as well as cl...
10 comments posted 22yrs
posted by riverstyx
10 comments posted 22yrs posted by riverstyx

Harbor Freight Tool Grinder

The HF grinder oft discussed in this column is $119.99 in sales flier 9190 received in today's mail. Price good til the...
3 comments posted 22yrs
posted by ghirardi
3 comments posted 22yrs posted by ghirardi

Gingery furnace has been fired

Anyone interested in my progress on the Gingery lathe project can find pictures here: http://physeeks.dyndns.org:8000/g...
51 comments posted 22yrs
posted by physics_seeker
51 comments posted 22yrs posted by physics_seeker

FA: Ring Grip Quick Release Pins 3/8" Diameter

FYI: I have up for auction 3 lots of ten 3/8" Quick Release Pins. Lane (The email address I used to post this to RCM is...
0 comments posted 22yrs
posted by googlegroupsposting
0 comments posted 22yrs posted by googlegroupsposting

OT: Plastics?

My eldest son & I have decided to make an acrylic (and other materials) case for a computer. Only because we can. Tryin...
7 comments posted 22yrs
posted by jparkhill.hatespam.
7 comments posted 22yrs posted by jparkhill.hatespam.

Need source for AL tubing spacers

I am looking for AL spacer rings that are 5/8" od 1/2" id 5/32" long ...or there about. I need just a hundred to start b...
6 comments posted 22yrs
posted by tom
6 comments posted 22yrs posted by tom

Making a hole in thin flat spring

I want to make a hole in the end of a linear spring that came from a tape measure. It is 1/2" x .005 and very hard. I t...
1 comments posted 22yrs
posted by bobengelhardt
1 comments posted 22yrs posted by bobengelhardt

Dayton grinder motor vibration

I have an old Dayton grinder, 1800 RPM motor. When it is running, it makes a loud humming sound. When it is turned off,...
6 comments posted 22yrs
posted by spencer313
6 comments posted 22yrs posted by spencer313

MSC Catalogue

I have been cruising through the latest MSC catalogue. It is very informative, in so much that it alerts the reader to...
4 comments posted 22yrs
posted by stevenospam
4 comments posted 22yrs posted by stevenospam