⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

FYI tool and cutter regrinding

It's an old problem, I've got a Kennet but quite frankly it, and I, have limits when it comes to regrinding end mill cu...
0 comments posted 17yrs
posted by fasand.words
0 comments posted 17yrs posted by fasand.words

MEW and ME

I see that David Clark the editor of MEW has now taken over the editorship of ME as well. Hopefully it may breath some f...
18 comments posted 17yrs
posted by john
18 comments posted 17yrs posted by john

Accurate pillar drill

Looking for a better pillar drill (perhaps with an XY moveable table, but ..) for more accurate work. Don't need huge,...
1 comments posted 17yrs
posted by zenadsl6186
1 comments posted 17yrs posted by zenadsl6186

Whitworth impact sockets

I'm looking for some Whitworth impact sockets. Does anyone have a source, or have any they would like to sell me? We're...
12 comments posted 17yrs
posted by duttondock
12 comments posted 17yrs posted by duttondock

UNF Thread

Hi Im making a TDC/Timing tool for a 2stroke engine By fitting a 5/16 unf bolt inside a spark plug. I need to know how m...
17 comments posted 17yrs
posted by user
17 comments posted 17yrs posted by user

Origin of Morse Tapers series

Please forgive me if this has been bashed out before, but I've been thinking again (Oh NO! they cried). For years I've...
25 comments posted 17yrs
posted by nadejack
25 comments posted 17yrs posted by nadejack

metal stockist devon

Can anyone suggest a good metal stockist in the South Devon area. There are plenty of tool shops near to me, but so far...
5 comments posted 17yrs
posted by ta_gilpin
5 comments posted 17yrs posted by ta_gilpin

Atlas 10f - Project

Is anyone looking for a "project"? I have an Atlas 10f which is complete (without chucks but including changewheels) bu...
18 comments posted 17yrs
posted by jontom_1uk
18 comments posted 17yrs posted by jontom_1uk

Milling problem

I have a Dore-Westbury milling machine which is in good condition, and allowing for its light construction, has general...
19 comments posted 17yrs
posted by mike.crossfield
19 comments posted 17yrs posted by mike.crossfield

IP44 50volt socket needed

I've got a toolpost grinder with a 50volt AC IP44 plug, serial numebr LN9021, and therefore need a matching panel mount...
4 comments posted 17yrs
posted by wells_hall
4 comments posted 17yrs posted by wells_hall

OT: Looking for 44 pin IC socket

Somewhat OT I realise, but knowing a few of the group are electronics enthusiasts (or just do it for a living), I thoug...
3 comments posted 17yrs
posted by aholeintheground
3 comments posted 17yrs posted by aholeintheground

movies

http://www.onlinehollywoodfun.blogspot.com Hii=85Click image xxxxxxx Hi=85Visit Me Hi..Click me
0 comments posted 17yrs
posted by bfatima8
0 comments posted 17yrs posted by bfatima8

Extra, extra, long end mill sought

Looking for some sort of rotary cutter, like an end mill, that is around 6 or 7 inches long, and has at least a 5 inch...
8 comments posted 17yrs
posted by emimec
8 comments posted 17yrs posted by emimec

Southbend bed regrind

A friend of mine* is looking to get a bed regrind for his 9" x 36" Southbend lathe (vintage 1946). Inverted V-bed. Does...
5 comments posted 17yrs
posted by david
5 comments posted 17yrs posted by david

Myford super 7 half nuts

Hi Can anyone tell me the proper procedure for installing and adjusting the half nuts on a Super 7? Pete Harrison
1 comments posted 17yrs
posted by peter.harrison
1 comments posted 17yrs posted by peter.harrison