⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6251 Threads Posts
to

Welding mild steel to stainless

I am making a little holder for an air lubricator (almost no load to be carried) and would like to weld a couple of lit...
14 comments posted 20yrs
posted by ignoramus1869
14 comments posted 20yrs posted by ignoramus1869

tips for welding small aluminum bosses?

I'm TIG welding a short section of 1/2" diam aluminum rod into a hole in 1/8" aluminum plate (which has already been we...
5 comments posted 20yrs
posted by vandeweg
5 comments posted 20yrs posted by vandeweg

Any recent reports on Boeing Surplus?

I'm heading up to Seattle in a couple days for the ABANA conference and I'm wondering if it would be worthwhile to visi...
4 comments posted 20yrs
posted by no_spam
4 comments posted 20yrs posted by no_spam

Web site address for welding

Good afternoon group Some time back there was a web site created for welding, most articles and graphics were from user...
0 comments posted 20yrs
posted by johnanoon
0 comments posted 20yrs posted by johnanoon

compact belt sander as a grinder

I am looking for a better solution than a small 4 1/2" hand grinder for grinding inside corners and other tight areas....
2 comments posted 20yrs
posted by rick.fetters
2 comments posted 20yrs posted by rick.fetters

Tig Welder Selection

I realize this is probably asked often, but I will continue nonetheless. I am in the market for a new TIG machine. I am...
4 comments posted 20yrs
posted by chrisgay
4 comments posted 20yrs posted by chrisgay

Welding around a circumferance

Stupid question from a dauber...sigh.. Lets say I want to tig an upright cylinder to a flat plate. What is the best way...
19 comments posted 20yrs
posted by gunner
19 comments posted 20yrs posted by gunner

Welding 1/4" NPT black iron pipe tee fittings

I want to tig weld several tee fittings (1/4" NPT black pipe), to make a air manifold. Any tips for good welds? Do I nee...
10 comments posted 20yrs
posted by ignoramus4106
10 comments posted 20yrs posted by ignoramus4106

readywelder review

With much talk about readywelders over the past few months I decided to pick one up. My application is two fold , I do...
1 comments posted 20yrs
posted by AndrewV
1 comments posted 20yrs posted by AndrewV

Lincoln Precision TIG 185 parts?

Hello all, I really like my Lincoln Precision TIG 185 and (as a beginner) I have been able to progressively improve my...
4 comments posted 20yrs
posted by sam48
4 comments posted 20yrs posted by sam48

Pulsed TIG

Now that I redid my CyberTIG to use a modern microcontroller, I have a question. Just when is pulsed TIG necessary? It...
3 comments posted 20yrs
posted by ignoramus28437
3 comments posted 20yrs posted by ignoramus28437

Welding helmet light attenuation characteristics

Hi all: For years I have been welding with a Jackson ECQ 3N1 Executive welding helmet. And for years I have had problem...
10 comments posted 20yrs
posted by ramray
10 comments posted 20yrs posted by ramray

bend radius

I've got a dumb question....... if I see on a blue print that there is a piece that has a corner with a 0.25" bend radiu...
5 comments posted 20yrs
posted by arwolkowski
5 comments posted 20yrs posted by arwolkowski

Connector types for Miller equipment

I need to build an adaptor from the 10 pin Amp connector on a millermatic 250 to the 14 pin male cord on a 22a wire fee...
2 comments posted 20yrs
posted by sdwheaton
2 comments posted 20yrs posted by sdwheaton