⋐⋒⋐ Computer Numeric Control

  1. Home
  2. ⋐⋒⋐ Computer Numeric Control
2667 Threads Posts
to

How do you make the sharpest chip?

How do you make the sharpest chip? With really dangerous sharp edges ... the ones hardest to dig out of feet, fingers &...
4 comments posted 16yrs
posted by Clhuprich
4 comments posted 16yrs posted by Clhuprich

Run your probe from your cam!

********start******** var#20 = .2500 (input the diameter to probe); var#21 = 1.2500 (input x center); var#22 = 1.2500 (...
5 comments posted 16yrs
posted by vinny
5 comments posted 16yrs posted by vinny

Superfast Laser

A buddy of mine is the head of a good sized metal shop in my area. His laser cutter is really fast.... http://www.youtu...
7 comments posted 16yrs
posted by duck
7 comments posted 16yrs posted by duck

halogen work light replacement lens

The lens on my work light shattered as I was blowing coolant off the work peice. Bad day yesterday. Where can you get n...
2 comments posted 16yrs
posted by rbraun333
2 comments posted 16yrs posted by rbraun333

About machines with corner control...

There's machines that lower the feed as needed to hold a location within a tolerance. But....that sux. The reason is th...
10 comments posted 16yrs
posted by vinny
10 comments posted 16yrs posted by vinny

Lathe chuck jaws...

Awl -- I got a nice-ish Poland 10" 3-jaw chuck, of course with no jaws -- PUL-M10L1ZD, #4673. I want to use this in pla...
14 comments posted 16yrs
posted by UNfitcat
14 comments posted 16yrs posted by UNfitcat

5C snap handle for fadal rotary....

Awl -- Got one, from http://www.jfkprecisionproducts.com/leverclosers.htm and it works OK -- the picture you see there...
0 comments posted 16yrs
posted by UNfitcat
0 comments posted 16yrs posted by UNfitcat

After a few days of studying chaining....

I now consider UGNX the best chaining software Iv'e ever used. And the best part is, Iv'e only scratched the surface. S...
21 comments posted 16yrs
posted by vinny
21 comments posted 16yrs posted by vinny

FS/Blueprint drawers

Im starting to sift through the stuff that I got out of the factory I recently shut down in Anaheim California. Current...
0 comments posted 16yrs
posted by gunner
0 comments posted 16yrs posted by gunner

NEW "chaining" thread....

The last one was a washout. So the new question is...does the system you run chain worth a frig? UG...truth is I can't...
2 comments posted 16yrs
posted by vinny
2 comments posted 16yrs posted by vinny

CNC-buffer for data exchange with CNC machine

CNC-buffer is the pocket electronic device providing with the functions of NC programs storing (from a PC or a NC) and...
0 comments posted 16yrs
posted by darkstar
0 comments posted 16yrs posted by darkstar

Thread on chaining...

Does your cam system chain worth a frig, and do you have any tips for making it work, like using plane masks, etc... Th...
9 comments posted 16yrs
posted by vinny
9 comments posted 16yrs posted by vinny

G Arc codes

just seeking reassurances. A typical and simple arc in the XY plane would be something thus. % G21 G00 G40 G54 G90 X0 Y...
3 comments posted 16yrs
posted by NotTodayThankyou
3 comments posted 16yrs posted by NotTodayThankyou

Mitsubishi HA80 CS Servo Motor- Which drive to use

Dear All. greetings. I have 2 Servo motors Mitsubishi HA80 CS on my Rotary /Tilting table, that I bought Used. There ar...
0 comments posted 16yrs
posted by bssainiji
0 comments posted 16yrs posted by bssainiji