⏣ General Metalworking

30778 Threads Posts
to

Update on solenoid for Onan generator

As some of you may remember, my generator works, except that the shutdown solenoid is broken. It would run great, but h...
6 comments posted 21yrs
posted by ignoramus7019
6 comments posted 21yrs posted by ignoramus7019

Miller Econotwin HF Question

Greetings all, I ran across an Econotwin HF in the garage of a guy that wants me to build him some parts out of Alum. p...
1 comments posted 21yrs
posted by jimnthem_AT_comcast_DOT_net
1 comments posted 21yrs posted by jimnthem_AT_comcast_DOT_net

propane tank as air tank?

Looking to use propane tank either two 20lb or one 40lb tanks as air tanks? I'll get new empty tanks FYI if this is doa...
15 comments posted 21yrs
posted by jpero
15 comments posted 21yrs posted by jpero

New shop/Garage floor

Hey all, I've been lurking here for a while, but now I have a real question. I've read about epoxy floor coatings befor...
9 comments posted 21yrs
posted by hangfirew8
9 comments posted 21yrs posted by hangfirew8

Shim Stock (Small Quantities)

I'm looking for a small amount (about 6" x 6") of steel shim stock. I tried MSC, Harborfreight, the usual suspects. They...
7 comments posted 21yrs
posted by rpm
7 comments posted 21yrs posted by rpm

RR track steel

I have about 500' of track with 2 switches that are an officially abandoned siding on my property. The thought was to s...
25 comments posted 21yrs
posted by tom(nospam)
25 comments posted 21yrs posted by tom(nospam)

HumVee Armor Facts

http://www.hundredpercenter.com/HumveeArmorFacts.html Gunner "To be civilized is to restrain the ability to commit mayh...
7 comments posted 21yrs
posted by gunner
7 comments posted 21yrs posted by gunner

m-head b'port

listers, need a bit of help. i purch a m-head b'port mill and as usuall,,,it had no manual. 1-where can i find one? 2-a...
1 comments posted 21yrs
posted by gustabone
1 comments posted 21yrs posted by gustabone

#3 vs #4 finish

What is the difference between a #3 and #4 brushed finish? Is the #3 finer?.....more decorative? Thanks.
4 comments posted 21yrs
posted by maberger
4 comments posted 21yrs posted by maberger

(OT) army takes care of its own?

Apologies for new thread, but server has =ABlost=BB old thread. Theirs was not to reason why, Theirs was but to do and...
17 comments posted 21yrs
posted by gmcduffee
17 comments posted 21yrs posted by gmcduffee

Re Metalcutting tool info sought

Hi Ed, thanks for your resonse. > If I may ask, what is the purpose of your inquiry? That may have an > influence on wh...
1 comments posted 21yrs
posted by c_finlayson
1 comments posted 21yrs posted by c_finlayson

Squaring Cross Slide on Craftsman 12x30 lathe

I own an older 12x30 Craftsman lathe model 101.07403. I am having a difficult time figuring out a quick an easy way to...
2 comments posted 21yrs
posted by terry.gaston
2 comments posted 21yrs posted by terry.gaston

3 Phase 184 Frame Motor/ 1800 RPM

I am going to put a larger motor in my lathe and it now has a 2HP 3 Phase 184 Frame Motor/ 1800 RPM from the 1950's mad...
2 comments posted 21yrs
posted by Sierevello
2 comments posted 21yrs posted by Sierevello

WTD: Boyar Schultz 612 Parts drawings

I picked up a basket case of a Boyar Schultz 612 surface grinder this morning from a local club member. As I didn't tak...
2 comments posted 21yrs
posted by escarcegaNOSPAM
2 comments posted 21yrs posted by escarcegaNOSPAM

Filling 5/8 holes with stick

Hi; I need to fill 3 holes that are 5/8" dia in 1/4 mild steel. I only have a stick welder. I will need to re-drill thr...
8 comments posted 21yrs
posted by bead_runner
8 comments posted 21yrs posted by bead_runner