⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30776 Threads Posts
to

Worth reading in ⏣ General Metalworking

Assessor information for 326 Olive Ave in Taft

The land, which Wieber does not own: http://assessor.co.kern.ca.us/propertydetails.php?srctext=03930304002&srctype=atn...
14 comments posted 8yrs
posted by george
14 comments posted 8yrs posted by george

This might just work !

tractor yesterday that's been beat to s*it ... the machine auto-engages the front wheel drive when the brakes are appli...
35 comments posted 8yrs
posted by snag_one
35 comments posted 8yrs posted by snag_one

120V water heater element

Hey Larry, IIRC you heat water with excess solar power, right? I noticed this 120V 2000W element while looking for some...
8 comments posted 8yrs
posted by muratlanne
8 comments posted 8yrs posted by muratlanne

Knife Control in the U.K.

http://www.powerlineblog.com/archives/2018/05/knife-control-in-the-u-k.php Posted on May 29, 2018 by John Hinderaker in...
2 comments posted 8yrs
posted by whiney_will_have_his_nose_in_my_ass_in_3_2_1
2 comments posted 8yrs posted by whiney_will_have_his_nose_in_my_ass_in_3_2_1

Mr Asch (and/or others) a benign question

Mr. Asch, (and/or others) Is there a better group system that you use instead of rec.crafts.metalworking? I remember it...
13 comments posted 8yrs
posted by smtpv1
13 comments posted 8yrs posted by smtpv1

Well pump questions and water softener

Hello, Q-1: We have a 1.5hp, 230v well pump at around 360ft. I was in the pump roo m today and the pressure switch kick...
7 comments posted 8yrs
posted by smtpv1
7 comments posted 8yrs posted by smtpv1

A beautiful sight

At least to me beautiful. Saturday I turned a bunch of aluminum castings for a customer. They are about 5 inches long a...
2 comments posted 8yrs
posted by etpm
2 comments posted 8yrs posted by etpm

ATTN: WhoYaKidding (and his ghost)

Wieber, the life-long dole-scrounger, chiseler and deadbeat, apparently once said, "I was a Democrat for 8 or more years...
3 comments posted 8yrs
posted by cap
3 comments posted 8yrs posted by cap

Rifled barrel

measures .875 at the receiver end . I'd like to build a bolt action handgun chambered ib .222 Rem , which has a cartrid...
3 comments posted 8yrs
posted by snag_one
3 comments posted 8yrs posted by snag_one

Are Jacks Worth It?

I often find myself cutting aluminum flat bar that extends beyond the jaws of the vise. When that happens it can result...
11 comments posted 8yrs
posted by none
11 comments posted 8yrs posted by none

Generator wiring question

Hi, I have a 1-1/2HP, 220v motor running from the dryer socket, all good. I was thinking of putting in a change over sw...
51 comments posted 8yrs
posted by davenpete
51 comments posted 8yrs posted by davenpete

Lincoln Welder electrical questions

Hi Guys, Two Welders: Welder 1: Weld-pak100. Is there any way to convert this to 220v? They make a similar 220 version...
5 comments posted 8yrs
posted by davenpete
5 comments posted 8yrs posted by davenpete

Chucking Reamers?

So what is the big difference in straight flute and spiral flute reamers... other than a few degrees. Seriously the spi...
3 comments posted 8yrs
posted by none
3 comments posted 8yrs posted by none

Beijing Precision Machine Tool Works

Looking at a machine... not working, but the price is right. It looks heavy though. A lot heavier than my little Hurco...
2 comments posted 8yrs
posted by none
2 comments posted 8yrs posted by none

Longitudinal feed gear

I have a 24-150. The longitudinal gear is worn and needs replacing. Anyone know where one is?
1 comments posted 8yrs
posted by Paparoy
1 comments posted 8yrs posted by Paparoy